Does the Erickson E-Track with Tie-Down Strap Meet DOT Standards

Question

Question:

Is item # EM58523 D.O.T. approved??

asked by: Mike

0

Expert Reply:

I spoke with my contact at Erickson who confirmed that the Erickson E-Track Wheel Tie-Down Strap with Roller Idler and Ratchet # EM58523 that you referenced does meet the DOT standards! This has a safe working load limit (WLL) of 1,100 lbs so you just need to make sure to use enough straps to accommodate the weight you will be carrying.

Attached is a review video for you to reference as well.

expert reply by: Jon G

0

Answer 1

I would run a set of e-tracks down the length of the floor of your trailer like part #E19148 (5 foot section), and then use the wheel nets like part #EM58523 to secure the wheels of your cars to the tracks. Check out the install videos I attached as…

view full answer...

Answer 2

You can use the 2-1/2 Inch Long Torx Screw, #TFX250, to attach your boards to your trailer frame. These screws do require a 7/32 inch pilot hole to be drilled through the board and trailer frame. Once the pilot hole is drilled, the screws will tap…

view full answer...

Answer 3

Ideally, you'll want some of the hardware attaching the e-track to the trailer floor to also secure to the cross members as well as to the planks that make up the trailer floor. If that's not possible, I'd recommend using a backer plate…

view full answer...

Answer 4

You can absolutely add a 3rd braking axle to your trailer. You will simply want to match your current axle for dimensions and capacity. I've linked the page to your options we carry to assist. Then you will need to change your hanger locations…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Justin, good question so I checked directly with Roadmaster for you, and verified the correct rock guard for the Roadmaster Direct-Connect Base Plate Kit #RM77VR on your Jeep Gladiator is the following: - Roadmaster Tow Defender Protective Screen…

view full answer...

Answer 7

Hey Dave, The Curt Custom Tail Light Wiring Kit for Towed Vehicles #C96JR would not be intertwined or interfere with the Blue Ox Patriot #BLU37TR. This wire harness is simply plugging into the motorhome and Gladiator tail lights to copy the light…

view full answer...

Answer 8

I reached out to Curt and they said there are no fitment issues with their Receiver #C74DR on your 2023 Jeep Gladiator Rubicon Diesel.

view full answer...

Answer 9

I'd love to help you choose the best parts for flat towing your 2024 Jeep Wrangler Unlimited! Here is what I recommend: - Direct-Connect Base Plate Kit #RM-521453-5 - Nighthawk All-Terrain Tow Bar w/ LED Lights #RM-676 - Curt Custom Tail Light…

view full answer...

Answer 10

I would be happy to help you set your 2022 Jeep Gladiator for flat towing. You're going to need a base plate kit, a tow bar, tow bar wiring, supplemental braking system, protective screen, charge line, stop light switch, and a high/low adapter. I…

view full answer...

Answer 11

The Curt Trailer Hitch Receiver item #C74DR fits both the Rubicon and standard or excluding Rubicon 2023 Jeep Gladiators. Our fitguide can be confusing when it comes to model break downs and this is another example of that. The Curt Trailer Hitch…

view full answer...

Answer 12

A check valve is needed for the brake booster air line when installing the Second Vehicle Kit #RM-98700. You will need to place one between the engine and tee with the red or black band on the check valve pointing towards the engine. I've…

view full answer...