Are Lug Nuts Included with the Dexter Trailer Hub Assembly, # AKIHUB-440-2-1K

Question

Question:

Hope I did not miss this info on the page. Just wanted to know if the lug nuts came with this hub assembly? Thank You

asked by: Dick N

0

Expert Reply:

The Trailer Hub Assembly, # AKIHUB-440-2-1K, does come with lug nuts in addition to the bearings, races, and seal.

expert reply by: Michael H

0

Answer 1

I believe I have what you are looking for. The Optronics Streamline LED Trailer Tail Light #STL79RB is most likely going to be the replacement you are wanting. Looking at your picture and comparing it to the #STL79RB I believe they are the same…

view full answer...

Answer 2

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 3

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

Hey David, Just to doublecheck I recommend measuring point B from the diagram below to see what your grease seal inner diameter is. If it's 1.25" and the inner diameter of the bearings is 1.00" then you would have a BT8 spindle and…

view full answer...

Answer 8

The trailer hub part #AKIHUB-440-2-1K matches exactly what you would need. Bearings, bolt pattern and stud dimensions are the exact same.

view full answer...

Answer 9

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 10

In order to match up the wheel studs for your Reliable 1206 hub, we'll need to know the full dimensions of the wheel stud you're replacing. In addition to the total length of the stud and its diameter and thread pitch, we'll also need to…

view full answer...

Answer 11

It would appear that that your 1978 Airstream had the standard 50 degree a-frame style coupler. You can verify this to ensure that the etrailer A-Frame Trailer Coupler #CA-5280-RB will fit correctly on your Airstream. I personally prefer the auto…

view full answer...

Answer 12

The standard a-frame coupler degree is 50 degrees but we do have a 32 degree coupler with the part #DM15633-81 but the rear width of it is 9-7/16 inches.

view full answer...

Are Lug Nuts Included with the Dexter Trailer Hub Assembly, # AKIHUB-440-2-1K

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching