Recommended Ball Mount for 2016 Toyota Tacoma TRD Off Road 4x4

Question

Question:

I am looking for an alternative to Toyota part number PT228-35161. This is a OEM Toyota ball mount for 2016 Toyota Tacoma. It has a 2 3/4 inch and a 1 1/2 inch rise and is rated at 10,000 lbs. Does e-Trailer carry an exact substitute for this Toyota part?

asked by: Mark R

0

Expert Reply:

I did some research on the Toyota OEM ball mount PT228-35161 and it has a 2-3/4 Drop or 1-1/2 inch rise and is rated for 10,000 lbs. We do not have an exact substitute for that ball mount, but a good alternative with some options is the etrailer.com Ball Mount Kit for 2" Hitches - 7,500 lbs # 989900. For a fixed mount ball mount I recommend measuring for level towing with your trailer. I've attached an article to assist. Another option is the etrailer.com Ball Mount Kit for 2" Hitches - 3/4" Rise or 2" Drop - 7,500 lbs # 989891.

If you prefer to have an adjustable ball mount option, I recommend the Rapid Hitch Adjustable, Aluminum Ball Mount Kit w/ 2 Zinc Balls - 4" Drop or Rise, # AM3462 and then the Andersen Trailer Hitch Lock and Adjustment Pin Lock Set # AM3493 to secure your investment. I've attached videos to assist.

expert reply by: Jason S

0

Answer 1

A popular trailer hitch for your 2014 Mazda CX-5 is the Curt Class-II #C12170. It will have a 3,500 pound towing capacity and 350 pound tongue weight capacity. I did some research on your CX-5 and it seems to have a 2,000 pound maximum towing…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 6

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

The Large Yakima OffGrid #Y07139 Cargo Basket uses crossbar clamps that are designed to be universal. They will fit virtually any crossbar shape, including most aftermarket and OEM crossbars. I was not able to find any schematics online that would…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...