Replacement Biker Bar Frame Bar for 1998 Harley Davidson Fat Boy

Question

Question:

I have touring base and bar in my trailer. Can I buy just the bar that will fit 1998 fat boy?

asked by: George M

0

Expert Reply:

The B&W Biker Bar Motorcycle Tie-Down System for Touring Harleys, part # BWMC2301, will not fit a Fat Boy frame but all you need is part # BWMC2302B fitted to the FB to be able to secure it to the base of your Touring model.

expert reply by: Adam R

0

Answer 1

I do have some parts for you but we aren't custom trailer builders and adding electric to a trailer is not a simple task. What I can tell you is that most interior lights are 12 volt so if you want outlets, lights, and shore power…

view full answer...

Answer 2

We have a 6-leaf 6k axle leaf spring with part #e94SR you could use on your 2016 Cruiser Lite 5th wheel that would give you a little more height. These are 26 inches long which is a really common size.

view full answer...

Answer 3

We have a 6 leaf 6,000 lb trailer axle leaf spring with the part #e94SR which would work well for you. It has the higher amount of leaves that you are wanting and is slightly higher rated. This will work great with your EZ flex system as well.

view full answer...

Answer 4

Actually yes. All of the Biker Bars use the same base, #BWMC2300. The clamping bar for touring bikes is #BWMC2301B and for the Heritage bikes the bar is #BWMC2302B.

view full answer...

Answer 5

Yes, the B&W Biker Bar Motorcycle Tie-Down Systems all use the same base and anchor kits. So all you would need to do is buy the Replacement Clamping Bar for B&W Biker Bar Motorcycle Tie-Down for Harley-Davidson Touring #BWMC2301B and replace…

view full answer...

Answer 6

You will have to measure the frame diameter on your Softail to determine if you will still be able to use the Clamping Bar #BWMC2301B from your B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson Touring #BWMC2301 will fit.…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 9

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 10

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

The hangers you currently have on your trailer are ones I have run into before. That being said, I spoke with MORryde and the #MR27ZR will still fit your trailer, but there is a modification that will need to be made. You’ll have to trim according to…

view full answer...

Replacement Biker Bar Frame Bar for 1998 Harley Davidson Fat Boy

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching