Atwood G6a7 Water Heater Replacement Gas Regulator

Question

Question:

thanx! do you carry a thermocouple for it?

asked by: Scott

1

Helpful Expert Reply:

The Atwood G6a7 water heater will need the Replacement Gas Regulator for Atwood Gas RV Water Heaters # 91602. I reached out to my contact at Dometic (who bought out Atwood) to confirm this fit and it is the replacement part you need for your G6a7 water heater.

expert reply by: Jason S

1

Scott

11/2/2018

thanx! do you carry a thermocouple for it?

Reply

Jason S.

11/2/2018

There are a number of universal fit thermocouples we carry. What you will need depends on the desired length. 12 Inch Long # CAM09253 18 Inch Long # CAM09273 24 Inch Long # CAM09293 30 Inch Long # CAM09313 36 Inch Long # CAM09333 48 Inch Long # CAM09353

Reply

Answer 1

The only tank equipped RV water heat option we currently offer is the Dometic RV Water Heater part #DMC74FR which is a 120 volt unit with 6 gallon tank and gas/electric operation. In regards to installation, this must be performed by a qualified…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 3

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 6

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…

view full answer...

Answer 9

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 10

The Furrion Single Zone Controller part #FACC12SA-BL does have a dip switch setup underneath the cover of it.

view full answer...

Answer 11

90-120 ft lbs of torque is probably about right for your trailer rims. If you check out the lug nut torque chart that I attached you will see that nearly all of the torque specs are that and higher.

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Atwood G6a7 Water Heater Replacement Gas Regulator

Products Referenced in This Question

Featured Help Information

Miscellaneous Media

Continue Researching