Inner and Outer Tube Outside Diameters of etrailer Trailer Jack # TJA-5000S-B

Question

Question:

trailer jacks are sold as a 2inch tube and a 2 1/4inch tube. Is this the outside tube diameter or the inside tube diameter?

asked by: Gary M

0

Expert Reply:

The etrailer trailer jack part # TJA-5000S-B that you referenced has an outer tube outside diameter of 2-1/4 inch and a inner leg outside diameter of 2 inches.

expert reply by: Jameson C

0

Answer 1

To replace the 4.80-12 size tires on your 2005 Viking Pop Up Camper, I recommend looking at the Taskmaster #AM30660. This 4.80-12 bias tire is mounted to a nice 12 inch white spoke wheel that has a 5 on 4-1/2 inch bolt pattern. The tire itself…

view full answer...

Answer 2

What you've got there looks like some type of proprietary mount that we don't offer. We do however have jacks that would work. I'd recommend having the mount removed and using a weld-on jack like the Fulton #FXP100W0301 and the #P9012-00…

view full answer...

Answer 3

1.9 inch is going to be a bit too small. Would 2 inch work? That's the closest we have like the Dutton Lainson part #DL22530 that you referenced. Maybe you could enlarge the hole with a dremel type grinder.

view full answer...

Answer 4

I may have a solution for you, but we don't have anything that matches your AL-Ko MD285 jack. You could likely make the Dutton Lainson #DL22530 jack you were looking at work, and you'd just need to add the caster #DL22414. This Dutton Lainson…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Inner and Outer Tube Outside Diameters of etrailer Trailer Jack # TJA-5000S-B

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching