Does Underbody Panel Get Reinstalled After Installing Curt Hitch # C13195 on 2019 Hyundai Santa Fe

Question

Question:

Hi experts. I am looking at the Curt hitch for my 2019 Santa Fe. I see that the under panel needs to be removed to install the hitch. Is this something that gets put back on at the end or do you lose it for good? Thanks for your help!

asked by: Max

0

Expert Reply:

When installing the Curt Trailer Hitch Receiver # C13195 on your 2019 Hyundai Santa Fe the underbody panel on the driver side will be removed but it will be reinstalled once the hitch is in place. I have attached a couple images of these two steps (Steps 2 and 9) from the installation instructions as well.

This Class III hitch is custom-fit for your Santa Fe meaning it will use existing holes in its frame for a no-drill installation. I have attached the complete installation instructions that you can also take a look at.

expert reply by: Chris R

0

click to enlarge

Answer 1

The Curt Trailer Hitch #C13195 for your 2019 Kia Sorento weighs in at just about 44 pounds while the Draw-Tite #75908 is a bit lighter at 39 pounds. Both feature identical 5,000 pound towing weight capacities but the Curt #C13195 does have a higher…

view full answer...

Answer 2

It looks like you might have left off the washers that need to be installed between the hitch and the bottom of the vehicle frame when you installed the Draw Tite hitch part #75908 on your 2019 Hyundai Santa Fe. Could I get you to check to see if the…

view full answer...

Answer 3

The best trailer hitch for a 2020 Hyundai Santa Fe is the Draw-Tite Trailer Hitch Receiver #75908 because it an easy, bolt-on installation, provides the most ground clearance of any hitch for your Santa Fe and has a tab which will let you very easily…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Does Underbody Panel Get Reinstalled After Installing Curt Hitch # C13195 on 2019 Hyundai Santa Fe

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching