Does Draw Tite Hitch for 2018 Jeep Renegade Hang Below or Through Rear Bumper

Question

Question:

Does the Draw Tite trailer hitch for my 2018 Jeep Renegade mount below or through the rear bumper?

asked by: Marty

0

Expert Reply:

For your 2018 Jeep Renegade the Draw Tite hitch part # 76021 that fits it hangs below the rear bumper as there would be no way to mount it through the bumper. I attached a picture that shows how it will look when installed. I also attached an install video for more info for you to check out too.

expert reply by: Jameson C

0

click to enlarge

Answer 1

We actually had the opportunity to install the Draw-Tite Max-Frame Trailer Hitch Receiver #76021 on a 2018 Jeep Renegade Latitude and found from the ground to the top of the receiver tube is 10-1/4". Since this is a 2" receiver we can…

view full answer...

Answer 2

Congrats on the new suv! Yes, there is a hitch for your 2023 Chevy Blazer. It is the Draw-Tite Max-Frame Trailer Hitch Receiver item #76023.This hitch is custom fit and bolts to your Blazer with included hardware. I really like this hitch because it…

view full answer...

Answer 3

The Curt trailer hitch part #C13418 is your best option for a trailer hitch for towing. This USA assembled hitch is very easy to install, has plenty of towing capacity and installs behind the rear bumper panel of your Blazer (see picture) so it's…

view full answer...

Answer 4

Yes, we have our etrailer Trailer Hitch Receiver #e36YR which fits all trims on your 2023 Chevrolet Blazer besides the premier trim. I prefer this receiver over others as it uses the matte black finish which best accents the OEM fascia trim and I…

view full answer...

Answer 5

Yes we have the etrailer hitch part #e36YR that is a confirmed fit for your 2023 Chevy Blazer. It install easily and has great towing capacities. If you need trailer wiring too the Tekonsha kit part #118720 is the easiest to install and has the most…

view full answer...

Answer 6

First you will need the etrailer Trailer Hitch Receiver #e36YR for your 2022 Chevrolet Blazer. This receiver will fit all trim levels with the exception being the premier. It is rated for up to 750lbs of tongue weight and a trailer weight up to…

view full answer...

Answer 7

When you install an aftermarket part on your vehicle like the Draw Tite hitch #76021 in this case on your 2018 Jeep Renegade, you are protected by the Magnuson–Moss Warranty Act. This act states, in part, that unless the installation and the part…

view full answer...

Answer 8

The Draw-Tite Max-Frame Trailer Hitch Receiver part #75699 which is a fit for a 2019 Jeep Grand Cherokee Limited X will install under the rear bumper fascia as will all of our trailer hitch options. I have attached a photo of what this will look like…

view full answer...

Answer 9

The reason you want to run the power wire all the way up to battery is so that you bypass all of the delicate wiring of your vehicle. The power wire is required on trailer wiring harnesses for some vehicles because the electrical system on those…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...