Dimensions of Hub and Drum Assembly # AKHD-545-2-EZ-1K

Question

Question:

What is the ID of the drum? Also what is the width of the braking surface?

asked by: Derrick M

0

Expert Reply:

The inner diameter of the hub and drum assembly, part # AKHD-545-2-EZ-1K, is 7 inches. It fits a standard 7 inch brake. The surface the brake pad contacts is 2-1/4 inches wide.

expert reply by: Charles S

0

click to enlarge

Answer 1

The reason for the price difference is the Dexter Trailer Hub and Drum Assembly #8-271-7UC3-EZ are only compatible with hydraulic brakes, where the #8-257-5UC3 are compatible with electric and hydraulic brakes. Since most people use electric trailer…

view full answer...

Answer 2

The braking surface on the Trailer Hub and Drum Assembly part #AKHD-545-2-EZ-1K is 2-1/4" wide. I went out to our warehouse to confirm this for you. If you need a set of braking assemblies to use with them, I recommend the Electric Trailer Brake…

view full answer...

Answer 3

I went out to the warehouse and pulled hub and drum assembly #8-173-16UC3 to measure it for you. From the surface where the wheel would sit to the end of the base of the drum is approximately 3-7/8 inches.

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Dimensions of Hub and Drum Assembly # AKHD-545-2-EZ-1K

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching