B&W Gooseneck Hitch Hole Location on Bed of 2016 Chevy Silverado 2500

Question

Question:

2016 Chevy 2500 shortbed 4 door B&W Goosneck hitch 4 inch hole measurements and will BWGNXA4085 work with it.

asked by: Corey L

0

Expert Reply:

If you check out the attached picture of the instructions for the B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1016 you can see that the center of the 4" hole will need to be 44-3/4" from the back of your 2016 Chevy Silverado 2500. This is only the bed and doesn't include the tailgate.

The 4" Offset Ball # BWGNXA4085 is compatible with this gooseneck hitch.

You may also be interested in adding a 7-Way connector to your bed with part # 50-97-410 to help make connecting your gooseneck trailer wiring easier.

expert reply by: Jon G

0

click to enlarge

Answer 1

Yes, the B&W Turnoverball Underbed Gooseneck Trailer Hitch #BWGNRK1016 is compatible with the Air Lift LoadLifter 7500 XL Air Helper Springs #AL57538 that you have on your 2017 GMC Sierra 2500. You will be able to use the 4" Offset Ball…

view full answer...

Answer 2

We do have gooseneck hitches that fit your 2018 Ford F-150 with a 5-12 foot bed. For that the best option is the B&W Turnoverball part #BW77FR which is a confirmed custom fit. B&W hitches are considered by basically all RVers to be the best…

view full answer...

Answer 3

It's very simple to know if you have the OEM Prep Package in your 2019 Chevy Silverado 2500. You'll just need to look in the bed of your truck, if you pucks like you can see in the attached picture then you have the prep package. If you do…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 7

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The Air Lift WirelessONE Compressor System #AL25980EZ and Air Lift WirelessONE Compressor System #AL25980 are nearly identical with only some very minor differences in CFM and duty cycle ratings. The #AL25980EZ will also come with an easier mounting…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

Hey Mark, since we know your Brinkley Z3100 has the Rhino style pin box, the correct Gen-Y fifth wheel to gooseneck adapter is the part #GY98GR which comes with the auto latch you mentioned wanting as well!

view full answer...