Solution for Needing Replacement Lens on 2009 Fleetwood Tioga

Question

Question:

I need a replacement porch light lens for my 2009 Fleetwood Tioga. The lens broke off but the length measures approximately 4 3/4 inch and is oval in shape. I have no idea what kind of light it is, the only identification that I can see is a US pat no D496751on the base. Clear or amber doesnt matter.

asked by: Richard W

0

Expert Reply:

Since we don't carry the exact light you have the best option we have for a replacement lens would be an all new assembly like the RV Porch Light part # RVPL7C that you referenced.

expert reply by: Jameson C

0

Answer 1

The lens on the RV Oval Porch and Utility Light #RVPL7C is held to the housing with some tabs on the lens that fit slots on the housing. To remove the lens you will need something thin and flat like a knife or small screwdriver to gently pry the…

view full answer...

Answer 2

You will need to either put some upwards or downwards pressure on the lens and then rotate it outwards to gain access to the inside of the RV Porch Utility Light w/ Switch #RVPL7C for changing the light bulb, mounting it, or replacing the Clear…

view full answer...

Answer 3

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

I have a solution that may work for you, but we do not currently have any 3" diameter submersible reverse lights. Have a look at the Optronics Backup Light #BU45CB which is a 4-1/4" diameter light that can be mounted to your trailer using…

view full answer...

Answer 10

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...