Higher Rated 2 Inch Pintle Hook Mounting Plate

Question

Question:

What is the Tongue Weight Capacity for: BWPMHD14005 - BWPMHD14004 - #C48210 - Thanks?

asked by: William W

0

Expert Reply:

Both parts # BWPMHD14005 and # BWPMHD14004 have a tongue weight capacity of 1,600 pounds.

Part # C48210 has a tongue weight capacity of 4,000 pounds.

So using that hook with either of those two mounts limits you to the lower 1,600 pound capacity.

For a higher rated mount the Buyers Products, part # 337PM1012, has a tongue weight rating of 2,000 pounds.

expert reply by: Charles S

0

Answer 1

If you have a 2 inch receiver opening on the vehicle you will be towing with the B&W Pintle Hook Mounting Plate, part #BWPMHD14005 may work well for you. The mounting plate features 7 holes on each side of the plate that are spaced 1-3/4…

view full answer...

Answer 2

You are pretty well balanced but given that the axles are the fulcrum (if you think of the trailer as a teeter totter) you have more weight on the long side. If you swap the positions of the Arctic Cat and the Honda/Timberwolf it would be a better…

view full answer...

Answer 3

The Demco Lunette Ring #DM09557-81 is approximately 3" wide and the holes are 1" apart center on center. This lunette ring fits in channel mounts like the Demco 6-Hole Adjustable Channel Bracket #DM59602.

view full answer...

Answer 4

Yes the B&W Pintle Hook Mounting Plate #BWPMHD14005 can absolutely be used in the rise position to raise the height of your pintle hook. This mounting plate fits 2" hitches, has a 15" shank and mounting holes that measure 3-3/8"…

view full answer...

Answer 5

While I'm not able to verify if the B&W Pintle Hook Mounting Plate #BWPMHD14005 can fit without bumper or spare tire interference in the rise position on your 2018 Jeep Wrangler Unlimited (we just haven't had a chance to test this), I did…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Higher Rated 2 Inch Pintle Hook Mounting Plate

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching