Recommended Best Trailer Hitch Receiver for Ground Clearance on 2018 Toyota Sienna
Question:
Is there a minimum hitch to ground height clearance on 2018 Toyota Sienna?
asked by: Jack
Expert Reply:
There is not a minimum clearance required by law for a trailer hitch, so you simply want to make sure you are able to travel without bottoming out your receiver. For instance, the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C13105 has a dimension of 12 inches from the inside top of the receiver which means approximately 9 inches from the ground to the bottom edge due to the lower the side brackets.
If you are concerned about that ground clearance restriction, then I recommend the EcoHitch Hidden Trailer Hitch Receiver - Custom Fit - Class III - 2" # 306-X7255 which will be approximately 10-3/4 inches from the ground. This is the best ground clearance you will find for a hitch receiver on your vehicle.
That height should allow you to go over speed bumps and driveway edges without issue unless your tongue weight causes significant sag on your rear suspension. To minimize that sag, you can use suspension enhancement like the Air Lift AirLift 1000 Air Helper Springs for Coil Springs - Rear # AL60732 to level your ride. If you go this route, you may also want the ability to change the air pressure at anytime using a compressor like # AL25592.
I've attached some videos to further assist.
If you will be towing with this hitch, I also recommend the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118498 for SE models or # 118648 for all other models. Then for a ball mount I recommend the ball mount kit # 989900 to give you the options needed for different trailers.
I've attached some videos to assist with these parts and their features.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
EcoHitch Hidden Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 525 lbs TW
- 3500 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- EcoHitch
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Air Lift Load Controller II Compressor System for Air Helper Springs - Single Path
- Air Suspension Compressor Kit
- Wired Control
- Single Path
- Analog Display
- Air Lift
more information >
Air Lift 1000 Air Helper Springs for Coil Springs - Rear
- Vehicle Suspension
- Rear Axle Suspension Enhancement
- Air Springs
- Light Duty
- Air Lift
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: EcoHitch Hidden Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Trailer Hitch
- Video: Trailer Hitch Installation - 2016 Toyota Sienna - Curt C13105
- Video: EcoHitch Hidden Trailer Hitch Installation - 2019 Toyota Sienna
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: trailer hitch
- Video: Choosing the Right Trailer Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Shop: Roof Rack
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: hitch
- Article: My Trailer Hitch Doesn't Fit
- Search Results: trailer hitch wiring
- Q&A: My Vehicle has a 4-Pin Trailer Plug, but Trailer has 7-Pin Trailer Plug
- Video: Curt Powered Tail Light Converter Installation - 2022 Toyota Sienna
- Shop: Brake Controller
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Article: Trailer Wiring Diagrams
- Search Results: bike rack
- Video: Choosing the Right Brake Controller
- Shop: Suspension Enhancement
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: wiring harness
- Article: How to Measure for Trailer Hitch Drop