Clearance Light to Replace Old Optronics Light 20327-02

Question

Question:

I need a replacement for an optronics amber clearance the only no. on the light is 20327-02, however it looks light your product MCL32ABB is the same light can you confirm? Thanks

asked by: Steve C

0

Expert Reply:

The original light, 20327-02, has been discontinued. You can instead use amber light # MCL32ABB in its place. This is an LED light. If you need an incandescent light then use # MC32ABB. I have linked some video reviews of these lights for you.

expert reply by: Michael H

0

Answer 1

What you will have to do to remove the old lid and install the new one is to first open the vent by turning the knob. With the lid open, go ahead and remove the screen, knob, and the control arm. The screws to the control arm can be difficult to…

view full answer...

Answer 2

We do indeed carry Optronics products. The number you provided is a DOT reference number, and does not denote the part number of the lamp or the lens. However we had a picture sent in once from a guy of the housing of the light he needed a lens for…

view full answer...

Answer 3

Optronics discontinued their light model 20327-02 some years back and we no longer have lens or base parts for it. You can instead use part #MC32RB for an incandescent light or part #MCL32RB for a high-efficiency LED type. Both have a white base.

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...