Mounting Hole Pattern for Fulton Trailer Jack FXP10

Question

Question:

I’m trying to replace the trailer jack and I know a question was asked, but the answer given was telling us what trailer tube thickness the jack would work with. I need to know what the center to center bolt pattern is on the jack plate to see if it will bolt up. My bolts center to center are 3” x 5.5”

asked by: John

0

Expert Reply:

On the Fulton Jack # FXP10 the center to center mounting hole spacing can be seen in the photo I linked for you. This 1200-lb-rated jack is intended for installation on 3 x 5-inch trailer frames.

expert reply by: Adam R

0

click to enlarge

Answer 1

Yes, about 99 percent of A-frame jacks use the same mounting pattern. The holes are generally 3 inches apart on center though it can vary ever so slightly which is why some jacks have slotted holes.

view full answer...

Answer 2

When using the Curt MV Weight Distribution System #C17052 or another weight distribution hitch you do not have to include the weight of the hitch in the tongue weight calculation for the trailer. So this hitch is rated for a trailer with 800-1,000lbs…

view full answer...

Answer 3

The mounting hole dimensions of A-frame jacks are a standard 3 inches apart on center, so you will need to weld your new jack on. I highly recommend the etrailer Round, A-Frame Jack #TJA-5000S-B, which has a 5,000 lb capacity and will give you…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

Yes, our Dexter leaf spring part #DX74XR is the same as the part number 072-079-00. This is a 7-leaf spring for an 8,000 lb trailer axle that is 24-7/8 inches.

view full answer...

Mounting Hole Pattern for Fulton Trailer Jack FXP10

Product Page this Question was Asked From

Continue Researching