Dimension of Curt RV Trailer Hitch Receiver # 13703 From Crossbar to Back of Bracket

Question

Question:

Hi, what is the dimension from the rearmost surface of the bracket to the rearmost surface of the receiver tube. I am trying to figure out if I will need to move my leveling jacks to install the hitch.

asked by: Wayne

0

Expert Reply:

The Curt Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703 has a measurement from the back of the crossbar to the back of the bracket of 6-1/2 inches. I've attached a photo to assist.

expert reply by: Jason S

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

SnapPads like the SnapPad XTRA Jack Pads for Lippert Leveling Systems w/ 9" Round Jack Feet - Qty 6 Item #SP54FR6 can be taken off and on as needed so you won't have to keep replacing them every time you need to take them off.

view full answer...

Answer 4

Hey Tim, thanks for reaching out! The Stromberg Carlson Base Pad Extreme for RVs and Trailers #SC33VR have a 6,000 lb rating for each Base Pad Extreme so you're looking at a total of 36,000 lbs for this kit of 6. Ideally your jacks will have the…

view full answer...

Answer 5

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 6

The Adjustable Width Trailer Hitch Receiver for RVs part #13703 is what I recommend for a Grand Design Solitude. It features a 3,500 lb gross trailer weight capacity and 350 lb tongue weight rating. This will be the most offered for a trailer as…

view full answer...

Answer 7

The puck feet on the Gen-Y Hitch Gooseneck Trailer Hitch for Dodge Ram OEM Puck Systems #GY83XR is just to help stabilize the ball mount and does not lock into place in the puck. The locking mechanism on top will lock the shank into the gooseneck…

view full answer...

Answer 8

If your Micro Minnie has a 4 inch x 4 inch channel bumper, I'd recommend the Curt #E-100. If you'd prefer a frame mounted hitch, I'd recommend the Curt #13703, which is compatible with box, C-channel or I-beam frames that are between 22…

view full answer...

Answer 9

The center to center measurement of the mounting bracket bolt-holes for the Stromberg Carlson Adjustable Accessory Hitch Receiver #SC45MR is 5-7/8". Additionally, there are two other bolts holes on the angle brackets that measure 3-1/8"…

view full answer...

Answer 10

The available trailer hitches for the 2016 Ford Transit T350 are not designed to fit the cab and chassis/cut away models but we do have options that you could use. The most popular option is #13703. It can actually be bolted on or welded on. Welding…

view full answer...

Answer 11

You will need to use a hitch mounted motorcycle carrier like the Ultra-Fab #UF48-979033 to carry your Honda Trail 125. This is required due to the weight of the Honda at roughly 250lbs. A bumper mounted rack like the Swagman #S64663 is only rated for…

view full answer...

Answer 12

For the hitch prep on a 2019 Cherokee Artic Wolf I believe the prep brackets will use the Lippert 1-1/4" Trailer Hitch Receiver for I-Beam Campers and Trailers - 68-3/8" Width #LC240220. You will need to measure the brackets to confirm the…

view full answer...