Replacement Handle and Square Bushing for the Fulton 1500 lb Marine Jack XP15L

Question

Question:

I apparently have the FXP15L Jack from the pictures. I havent found a model number on the jack yet. Just says Magnum Series on the top plastic cap. The handle bent and the square bushing broke. Need some parts.

asked by: Larry G

0

Expert Reply:

For the Fulton 1,500 lb trailer jack, # FXP15L, you will need the Replacement Sidewind Handle Kit, # F0933305S00. This kit includes the crank, pin and square bushing you referred to.

expert reply by: Robert G

0

Answer 1

Your best bet is going to be hardware kit #F0933325S00. The bolt is a 1/2 inch coarse threaded bolt with matching nut and bushing. But it sounds like the nut or bolt is backing out on your assembly. This could mean the lock washer is shot. You could…

view full answer...

Answer 2

You have two choices for a replacement handle for the now obsolete Reese trailer jack 74410. The first option is the Fulton Sidewind 800 lb Handle #F0933301S00. Your second option is the Fulton Sidewind 1500 lb Handle #F0933305S00. The dimensions…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

For your 2021 Chevrolet Blazer you're going to need to start with a base plate kit. Since there aren't any Blue Ox base plates I'd recommend going with the Roadmaster Direct-Connect Base Plate Kit #RM-523204-5. These are just as good as…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The correct replacement for the Fulton Magnum Series Trailer Jack on your trailer is the Fulton Bolt-Thru Swivel Marine Jack part #FXP10W0301 if you have a bolt-thru mounting bracket or part #FTJ120W0301 if you have a snap-ring mounting bracket. I…

view full answer...

Answer 7

The Replacement Sidewind Handle Kit, #F0933305S00, is going to work for Fulton jacks with up to a 1,500 lb capacity so this would work for your 1,000 lb Magnum series jack. Part #F0933301S00 is going to replace handles on Fulton jacks with up to an…

view full answer...

Answer 8

The Furrion Chill Replacement RV Air Conditioner for Dometic Brisk Setup - 15,000 Btu #FR42PV rooftop unit is fixed on the RV roof using 4 long bolts through the mounting frame from the interior of the RV ceiling. So you will need to be able to…

view full answer...

Answer 9

The correct brake controller install harness for a Tekonsha controller in a 2006 Chevy Silverado is the part #3015-P. If you want to easily install the controller this would be all that you'd need. It simply plugs into the controller and then to…

view full answer...

Answer 10

As long as the air bag mounting brackets do not mount in the same place on the truck frame as the B&W gooseneck brackets then you can install air bags on a 1999 Dodge Ram. Firestone kit #F2071 would not work because it mounts on the outsides of…

view full answer...

Answer 11

The correct wedge to use with a Curt A20 #C16140 and a Turning Point Pin Box is the wedge #C16992 that you referenced.

view full answer...

Answer 12

You do not have to change the connector or add the PWM filter that splices in; all you have to do is add an adapter that plugs into the 7-way of your 2023 Chevy Silverado to get the correct amount of power to your Furrion Vision S camera system. What…

view full answer...

Replacement Handle and Square Bushing for the Fulton 1500 lb Marine Jack XP15L

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching