Reese M5 Series 5th wheel Hitch Compatibility with 2019 Ford F-350

Question

Question:

When will you know if this hitch will fit my 2019 Ford F350 with factory installed puck system?

asked by: Bill

1

Helpful Expert Reply:

I reached out to my contact at Reese and the 2019 Ford Factory Puck System has not changed, so the Reese M5 Series 5th Wheel Trailer Hitch - Single Jaw - 27,000lbs # RP30922 will fit. The differences are only in the minor cosmetics like trim packages, colors, and wheels.

expert reply by: Jason S

1

Answer 1

The 1/2 inch bolts that attach the center section of the hitch to the legs should be torqued per the instructions linked below. If you need a torque wrench that covers that spec you can use #ALL944001. Reese M5 5th Wheel Trailer Hitch #RP30928 is…

view full answer...

Answer 2

You are definitely correct that both the B&W Companion #BWRVK3305 and the Reese M5 #RP30922 are fantastic 5th wheel hitches that will work well on your 2019 Ford F-350 but I do recommend going with the B&W Companion #BWRVK3305. The B&W…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 5

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 8

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 9

Beds shorter than 8 foot do commonly need a slider hitch David, but a lot of modern fifth wheel trailers are now made with tapered noses to help and in a lot of cases a slider isn't required. So if the trailer you plan to tow has a tapered nose…

view full answer...

Answer 10

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 11

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 12

A wedge is needed, yes, and the Lippert Turning Point pin box does come with a universal wedge, but it is not a very good fit with the B&W Companion #BWRVK3710. So I highly recommend instead using the 5th Airborne Custom Wedge for B&W Fifth…

view full answer...

Reese M5 Series 5th wheel Hitch Compatibility with 2019 Ford F-350

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching