Leg Extension for Lippert Electric Trailer Jack # LC285318

Question

Question:

I would like to have leg extension for my Lippert power jack. I bought one on Amazon but it is the wrong diameter. What is the correct diameter of the shaft and do you have one at a reasonable price. I would like one that adds about ten inches. Thanks

asked by: Ralph W

0

Expert Reply:

The Lippert Electric Trailer Jack # LC285318 that you referenced features an inner tube diameter of 2 inches. We do have a nice selection of jack feet that are compatible with this jack. The Husky Brute Super Foot Fold-Up Jack Foot # HT31610 will fit the jack and provides an extension of 7 inches. This is the largest extension we have available for this jack. It also features a spring-loaded cam lever so you can quickly fold the foot down for use or up for travel.

For a standard foot that will offer some extension we have the Lippert Drop Leg # LC405217 which will add 4-1/2 inches of extension.

expert reply by: Chris R

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 6

Hey Michael, thanks for reaching out! The EcoHitch #EH57FR sits a little higher than the Curt #C52NR so it will give you better ground clearance for your 2024 Chevy Silverado 2500. The EcoHitch is a bit more recessed into the front bumper than the…

view full answer...

Answer 7

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 8

Hey Tony, thanks for writing in, and that's a really smart question. The answer is yes, the fresh water tank should be full when adjusting the 16,000 lb Equal-i-zer Weight Distribution System #EQ90-00-1600. What you want to do is have the trailer…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

Hey Buddy, so the Fastway Adjustable Ball Mount part #DTSTBM6825-2S is a really great choice for the 2-1/2 inch hitch of your 2021 Ford F-250 which is going to be very solid in your hitch due to it's built in anti-rattle device that is easy to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...