Trailer Cover Needed for a 7' x 14' Enclosed Cargo Trailer

Question

Question:

I have an enclosed V-nose 7x14 cargo trailer, 16 ft long with V-Nose with 8ft tall side walls. Also it is 7 ft wide plus 9 inch fenders on both sides. Which cover would you suggest?

asked by: Dave

0

Expert Reply:

The closest thing that we have as a cover for your 7' x 14' trailer is a horse trailer like the Adco SFS AquaShed # 290-46004 which fits horse trailers that are 14'1" - 16' long.

These measure 80" wide for the box though so you will need to double check that your trailer is exactly 7' wide as that would be 84". The bottom of it does flare out though and will accommodate fenders that are a max of 106" wide. All of their horse trailer covers measure 94" tall which would be slightly too short.

If your trailer width ends up being 80" then you are good to use this cover! However, if your trailer really is 7' wide then your best option would be to get a custom cover made for your trailer.

expert reply by: Jon G

0

click to enlarge

David

11/1/2021

Have flat nose pace 7x14 dual axle motorcycle trailer. Need outside slip on cover to protect from elements as it is outside full time and always wet and raining here in Florida. Painted white. Color doesn’t matter. What do you have? David 386-624-3899

Reply

Les D.

11/2/2021

@David The Adco # 290-46004 mentioned above is your best bet. Let me know if you are thinking of something different.

Reply

Answer 1

The Adco SFS AquaShed Cover for Bumper Pull Trailer part #290-46004 would be an excellent option for a 7 x 14 V-Nose Enclosed Trailer. The Adco SFS AquaShed Cover for Bumper Pull Trailers is actually designed for horse trailers but it will work well…

view full answer...

Answer 2

For a cover that can be used on a cargo trailer that is 7 x 14 you can use a pop-up camper cover like the Adco Polypropylene RV Cover for Pop-Up Camper - Up to 16' Long - Gray #290-2894; this will work on a trailer that is up to 42" tall.…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Trailer Cover Needed for a 7' x 14' Enclosed Cargo Trailer

Product Page this Question was Asked From

Continue Researching