Trailer Wiring Needed for a 2017 Ford Transit T250

Question

Question:

trying to find a plug in trailer kit for a 2017 ford transit 250

asked by: Fred S

0

Expert Reply:

If your 2017 Ford Transit T250 came with the factory tow package then you simply need the Hopkins # HM40975 to add both a 7-Way and a 4-Way connector. This will plug into the US Car Connector at the rear of your Transit.

We also have kits that can be used if your Transit doesn't have the factory tow package. For basic trailer lighting functions use the Curt T-Connector # C56327 which plugs into connectors behind the tail lights on your Transit and are powered through the 12V lead that is routed to the battery.

If you need to upgrade that to a 7-way you can use our Universal Installation Kit # ETBC7.

If you are needing a brake controller then I highly recommend going with the Tekonsha Prodigy P3 # 90195. This is a proportional brake controller that will apply the brakes on your trailer at the same time and with the same intensity as the brakes in your vehicle. The best feature about this brake controller is the LCD screen that makes operation and diagnosing any problems much easier than an older controller that only uses codes.

Attached are some review videos and installation instructions for you to check out.

expert reply by: Jon G

0

Answer 1

Factory wiring could be any color since there is no one standard that all manufacturers follow. You will need to test the wires by function using a circuit tester such as #PTW2992 if you do not already have one. I have included a picture that shows a…

view full answer...

Answer 2

I took a look at the online version of the owner's manual for your 2018 Ford F-150 and was able to locate the wiring color code for the factory 7-Way trailer harness on the truck. The wires leading up to the factory plug are as follows: Yellow -…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

It is too small of a space to fit the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear - 4 Steps - 375lbs - Black Bracket Item #TLA7834 but you can instead mount it to the bumper of your camper like in the attached picture.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear #TLA7834 only comes in the silver color with the black brackets. The overall folded dimensions are 14" High x 23-1/4" Wide x 11" Deep which includes the bracket and…

view full answer...

Answer 7

I may have different installation method for you, but there is not an extended bracket made to push the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear #TLA7843 away from your camper to clear your bumper. It may be possible to have a…

view full answer...

Answer 8

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 9

The connection on the Seaflo Submersible Utility Pump #SE54FR is designed to fit a hose with an inner diameter of 13 mm.

view full answer...

Trailer Wiring Needed for a 2017 Ford Transit T250

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching