Torque Specs for the Lug Nuts on a 1999 Bonair 700 Tent Trailer

Question

Question:

Hi! We own a 1999 bonair 700 tent trailer, what would be the wheel torque specs. Thanks

asked by: Eric

0

Expert Reply:

The torque specs for the lug nuts on your 1999 Bonair 700 Tent Trailer is going to depend on the stud size, lug nut type, wheel size, and wheel material. Once you gather this information you can use the attached chart to find the correct torque specs.

I do not have the above information on your trailer so you will need to do a bit of investigating as I cannot give you an exact figure.

expert reply by: Conner L

0

click to enlarge

Answer 1

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith…

view full answer...

Answer 2

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures…

view full answer...

Answer 3

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this…

view full answer...

Answer 4

The best way to select the correct size vinyl trim insert is to measure the trim insert you have now while flat, not the track. We don't really recommend measuring the track as they are not all a standard width. That said, we only offer vinyl…

view full answer...

Answer 5

The difference between the letter D in your ST175/80D13 and the R in the tire size of the Wheel and Tire ST175/80R13 part #AM31985 that you referenced is the tire construction. D stands for bias-ply which is a less preferred tire construction,…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…

view full answer...

Torque Specs for the Lug Nuts on a 1999 Bonair 700 Tent Trailer

Product Page this Question was Asked From

Continue Researching