Replacement Hubs for a 2001 Forest River RV Flagstaff Folding Pop-Up Camper

Question

Question:

I have a 2001 forest river flagstaff pop up camper. I am needing an entire hub assembly. It’s a 4 lug and the bearing says : VPZ-15-MRI L44610

asked by: James

0

Expert Reply:

The correct trailer hub you need for your 2001 Forest River RV Flagstaff Folding Pop-Up Camper is the Trailer Idler Hub Assembly part # AKIHUB-440-2-2K. I have attached an install video for you as well.

expert reply by: Conner L

0

Answer 1

In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first thing you will need to know is the bolt pattern of your hubs. This is so you get a hub that is compatible with your…

view full answer...

Answer 2

BTR and BT8 are the reference numbers for a standard trailer spindle size. When picking out a hub for a trailer you have to make sure that the hub is designed to fit the spindle. What you will need to do is measure spindles on your trailer where…

view full answer...

Answer 3

The #168233 Double Lip Grease Seal has an outside diameter of 2.332 inches and an inside diameter of 1.688 inches. This seal is not compatible with a AF2527E seal with a O.D 2.312, because, even though the O.D. id very close, the inner diameter of…

view full answer...

Answer 4

One of the most popular tire/wheel combinations that we have to offer with a 4 on 4" bolt pattern is the Kenda Karrier S-Trail ST145/R12 Radial Tire w/ 12" White Spoke Wheel #AM35351DX. Since the 4 on 4" bolt pattern is the…

view full answer...

Answer 5

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 6

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Replacement Hubs for a 2001 Forest River RV Flagstaff Folding Pop-Up Camper

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching