Replacement Brake Magnet for 12 Inch Dexter Braking Assemblies

Question

Question:

Hi, I have Dexter 008-219-13 drums which I believe are 12inch I am looking to get some magnets but not sure if I can use the KB12E-06 Trailer is a 12,000 GVW dual axle Please advise

asked by: Joe

0

Expert Reply:

Yes, the Replacement Magnet Kit for 12" Electric Trailer Brake Assemblies part # AKBRKR-M12 which is the same as part KB12E-06 will work for you. The Dexter Trailer Hub and Drum Assembly part # 8-219-13UC3 that you referenced is for a 12" braking assembly so if this is the hub/drum that you have then the above magnet will work great for you.

expert reply by: Conner L

0

Answer 1

Brake magnets such as the Replacement Magnet Kit #AKBRKR-M12 on trailer electric brake assemblies are non-polarized. When installing an electric brake assembly, like the Right Hand 12" #AKEBRK-7R-SA, either wire can be used for the brake signal…

view full answer...

Answer 2

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 3

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 9

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Replacement Brake Magnet for 12 Inch Dexter Braking Assemblies

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching