Is there a Locking Anti-Rattle Hitch Pin for Curt Platform Bike Racks

Question

Question:

Do you sell a locking anti rattle hitch pin for the Curt 18086 bike rack?

asked by: Jim W

0

Expert Reply:

Curt bike rack 18086 does not have a locking anti-rattle hitch bolt option. What we recommend is to use the regular hitch bolt and then use a cable lock, # C23666, to secure the bikes and rack to the hitch by running the cable through the hitch safety chain loops. I have linked a video review of this cable lock for you.

expert reply by: Michael H

0

Answer 1

The Yakima EXO Swing Away 2 Bike Rack w/ Cargo Carrier - 2" Hitches #Y54ZR is an excellent 2 bike rack option which can be used with or without a cargo basket. There are many other Exo system items that can be used with this system, one of which…

view full answer...

Answer 2

If you wanted to remove some of the wheel trays of the Hollywood Racks Destination bike rack part #HR4000 you certainly could as like you said they are all bolted on independently.

view full answer...

Answer 3

Yes, Swagman Skaha 2 Plus Bike Rack with Cargo Carrier #S69SR will fit and work on your Toyota Sienna as long as it is equipped with a 2 inch trailer hitch receiver.

view full answer...

Answer 4

The anti rattle pin on the Curt 4 premium #C18087 is a threaded pin so a J-Pin stabilization device like you have will not fit the pitch of the thread in the shank. Honestly, you will get a decent amount of movement with any 4 bike platform rack. To…

view full answer...

Answer 5

Yes, the Curt bike rack part #C18087 that you referenced is designed for exactly what you mentioned. It can be used as either a 2 bike or a 4 bike rack. The outer tray section can be removed to make it a 2 bike rack when needed.

view full answer...

Answer 6

Hello, not knowing your exact vehicle type I can not give you exact numbers. The measurements are from the center of the hitch pin hole. The Curt 4 Bike Platform Rack #C18087 will be approximately 13-15 inches to the first wheel hoop. It will have…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The Kuat Sherpa 2.0 #SH22G and the NV 2.0 #NV22G that you referenced are both excellent platform-style racks that will hold your bikes by the front wheels with no frame contact. These are top-of-the-line carriers and you really would not go wrong…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 12

There are some subtle difference between the Kuat Piston Pro Bike Rack for 2 Bikes #KU76ZR and the Kuat Piston Pro X Bike Rack for 2 Bikes #KU98VR. Overall the two racks are very similar, there are just some subtle differences/upgrades on the Piston…

view full answer...

Is there a Locking Anti-Rattle Hitch Pin for Curt Platform Bike Racks

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching