Troubleshooting Installation of Curt Wiring Harness on 2015 Honda CR-V EX-L

Question

Question:

Hi I Buy a Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector Item # C56158 for a CRV EXL 2015 But it did not work, and I see that my blue connector, does not have the thick red cable that connects to the red cable that brings the fuse into the harness, can you help me?

asked by: Ruben D

0

Expert Reply:

My contact at Curt Tech said their harness # C56158 is a fit for your vehicle. He said that some later model vehicles had a second blue connector that had the wire you are seeking, so you may want to grab a flashlight and see if there is another blue connector. He also said to make sure your fuse is in the correct location in your box. I've attached a video as well as their installation instructions to help further.

If you need further help, let me know.

expert reply by: Jason S

0

Answer 1

The fact that your motorhome has a Diesel engine won't have any bearing on the parts you need to correct the problem you're experiencing. In order to flat tow your CR-V without discharging the battery, you'll need to remove…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Troubleshooting Installation of Curt Wiring Harness on 2015 Honda CR-V EX-L

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching