Recommended Coupler Lock for Demco Channel Tongue Coupler with eZ-Latch

Question

Question:

looking for a lockable coupler pin for item #DM13203-95. thanks.

asked by: Eric

0

Expert Reply:

The Demco Channel Tongue Trailer Coupler - Zinc - 2-5/16" Ball - 3" Channel - Bolt On - 18K # DM13203-95 has an integrated 5/16 inch pin hole with a 3 inch span for that lockable feature. I recommend using the Trailer Coupler Lock # e98888 which has a 3-3/8 inch span and is 1/4 inch diameter.

For further security when disconnected from your vehicle, I recommend the etrailer.com Coupler Lock # e98894.

expert reply by: Jason S

0

Answer 1

I went out to the warehouse to take some measurements of the Titan Zinc-Plated Straight-Tongue Coupler #T4853100 for you. Based on the measurements, the Titan #T4853100 will not fit into a 4 inch square tube. The width of the coupler is 3-3/8 inches.…

view full answer...

Answer 2

We do have a variety of straight tongue couplers that fit with a 2-5/16" hitch ball like what you're looking for. We have standard couplers like the Demco #DM13203-95 as well as hydraulic actuator couplers like the Demco #DM8101801. I'm…

view full answer...

Answer 3

I can absolutely explain how the etrailer Trailer Coupler Lock for your flat lip coupler works, and it is extremely simple. What happens is you will slide the lock over your flat lip coupler, and push the pin up - it won't take any strength at…

view full answer...

Answer 4

More than likely the reason you are having issues with your hitch sliding back and forth is that your coupler is still articulating. To stop it from articulating there are a few options. You can do so by drilling holes in either side and sliding a…

view full answer...

Answer 5

We do offer a few repair kits for 2-5/16-inch straight channel couplers, such as parts #DM6008 and #DM5817 for Demco couplers. These and all other repair kits are shown on the linked page. If you find you need to replace your straight 2-5/16-inch…

view full answer...

Answer 6

All the channel tongue couplers we offer are fits for a 3 inch channel, but I do have a solution. You could use the Demco #DM13203-95 channel tongue coupler, and shim each side of the channel tongue out using some 1/2 inch steel plate. This would be…

view full answer...

Answer 7

I went out to our warehouse to take a look at the Buyers Products Straight Tongue Trailer Coupler #3370091562 you referenced and I measured a distance of right at 7/8" from the inside top of the coupler down to the center of the mounting holes.…

view full answer...

Answer 8

The distance from the rear mounting hole to the end of the Demco Channel Tongue Trailer Coupler, part #DM13203-95 is 1-3/4 inches. I have attached a photo of the coupler with the dimension shown you can check out.

view full answer...

Answer 9

Yes, the Blaylock EZ Lock Trailer Coupler Lock #BLTL-33 that you referenced does fit the Demco Channel Tongue Trailer Coupler #DM13203-95 that you referenced. The max diameter shackle you could fit through the hole on the 3/4 inch long pin is 3/8 of…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The Trimax Puck Lock for Trailer Door Hasps #TMX96RR cannot be keyed alike. While disappointing I'm sure, there is another option to consider, which is to order a quantity of two of the Trimax Puck Locks for Trailer Door Hasps #TMX73FR. The…

view full answer...

Answer 12

Thank you for the image. It appears you will need either the Demco Channel Tongue Trailer Coupler #DM13203-95 or #DM16080-95. Both of these couplers have a zinc coating for increased corrosion resistance and fit on a standard 3" wide channel…

view full answer...