Distance From Rear Edge Of Demco Channel Tongue Trailer Coupler To Mounting Hole

Question

Question:

What is the measurement from the outside edge of this coupler to the mounting holes?

asked by: Laura

1

Helpful Expert Reply:

The distance from the rear mounting hole to the end of the Demco Channel Tongue Trailer Coupler, part # DM13203-95 is 1-3/4 inches.

I have attached a photo of the coupler with the dimension shown you can check out.

expert reply by: Jeffrey L

1

click to enlarge

Answer 1

More than likely the reason you are having issues with your hitch sliding back and forth is that your coupler is still articulating. To stop it from articulating there are a few options. You can do so by drilling holes in either side and sliding a…

view full answer...

Answer 2

I went out to the warehouse to take some measurements of the Titan Zinc-Plated Straight-Tongue Coupler #T4853100 for you. Based on the measurements, the Titan #T4853100 will not fit into a 4 inch square tube. The width of the coupler is 3-3/8 inches.…

view full answer...

Answer 3

All the channel tongue couplers we offer are fits for a 3 inch channel, but I do have a solution. You could use the Demco #DM13203-95 channel tongue coupler, and shim each side of the channel tongue out using some 1/2 inch steel plate. This would be…

view full answer...

Answer 4

I went out to our warehouse to take a look at the Buyers Products Straight Tongue Trailer Coupler #3370091562 you referenced and I measured a distance of right at 7/8" from the inside top of the coupler down to the center of the mounting holes.…

view full answer...

Answer 5

We do offer a few repair kits for 2-5/16-inch straight channel couplers, such as parts #DM6008 and #DM5817 for Demco couplers. These and all other repair kits are shown on the linked page. If you find you need to replace your straight 2-5/16-inch…

view full answer...

Answer 6

On the Demco Channel Tongue Trailer Coupler #DM13203-95 the three top row mounting holes' centers are 1-inch from the top flat surface of the coupler. I went to our warehouse and took this measurement to confirm. This and other dimensions are…

view full answer...

Answer 7

The Demco Channel Tongue Trailer Coupler - Zinc - 2-5/16" Ball - 3" Channel - Bolt On - 18K #DM13203-95 has an integrated 5/16 inch pin hole with a 3 inch span for that lockable feature. I recommend using the Trailer Coupler Lock #e98888…

view full answer...

Answer 8

We do have a variety of straight tongue couplers that fit with a 2-5/16" hitch ball like what you're looking for. We have standard couplers like the Demco #DM13203-95 as well as hydraulic actuator couplers like the Demco #DM8101801. I'm…

view full answer...

Answer 9

Yes, the Blaylock EZ Lock Trailer Coupler Lock #BLTL-33 that you referenced does fit the Demco Channel Tongue Trailer Coupler #DM13203-95 that you referenced. The max diameter shackle you could fit through the hole on the 3/4 inch long pin is 3/8 of…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...