Availability of Tandem-Axle Suspension Kit with Triangular Equalizer # TREQ310

Question

Question:

do you have a kit like Item # K71-359-00 but with Dexter equalizers 13-10 6” horiz. x 4” vert. centers ?

asked by: David

0

Expert Reply:

We do have all the items you need, however the TruRyde Triangular Equalizer # TREQ310 that you referenced is not available in a complete suspension kit.

In order to use this 6-1/16 inch long, 4 inch tall equalizer, you will just need 8 of the Shackle Straps # 115052 and 14 Wet Shackle Bolts # 126B2. I have also attached a link that will take you to our available selection of hangers if they are needed.

expert reply by: Chris R

0

Answer 1

I do have an upgrade option for your 6-1/16" long, 4" tall Equalizer #TREQ310, and since you don't want to lower the ride height with the E-Z Flex #K71-652-00, I recommend going with an option from MORryde, as the Equa-Flex are just too…

view full answer...

Answer 2

There is not an equalizer that will give you that height in the center. The #TREQ310 you already have are the tallest standard equalizer with the 4 inch center to center height. If you need to add 2 inches to your system, you will either need to…

view full answer...

Answer 3

You can substitute the Road Armor Shock Absorbing Equalizer Kit #LC696740 for your Triangular Equalizer #TREQ310 but you will need to get shorter shackle straps as well. They both have the same side to side measurement for the wet bolt holes but the…

view full answer...

Answer 4

The E-Z Flex Heavy Duty Rubber Suspension System part #K71-652-00 will work in place of your existing equalizers part #TREQ310. The main measurement you will want to be concerned of is the distance between the two lower most bolt holes. The distance…

view full answer...

Answer 5

There are a couple of things to look at for your setup. Since you said you have a 6-1/2 ft bed on your 2005 Ford F-150, I assume you have a sliding hitch installed. You also said you have also maxed out your trailer arm. My guess is you are talking…

view full answer...

Answer 6

When lining up the axis of the wet bolts it does not matter if the 90 degrees is forward or back. As long as it's either you are good!

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 12

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...