How Tall is Replacement Wheel Master Lug Nut Cover # WMRMT9061

Question

Question:

HEIGHT?

asked by: D H

1

Helpful Expert Reply:

I measured the Replacement Wheel Master Lug Nut Cover # WMRMT9061 and it has an overall height of 1.6 inches.

expert reply by: Michael H

1

click to enlarge

Answer 1

Although we do not have a direct replacement for the Dicor V19582-EJN, the Replacement Wheel Master Lug Nut Cover for Wheel Liner - Qty 1 #WMRMT9061 will fit a 22 millimeter lug nut. From what I have found, the jam nut you are looking for has been…

view full answer...

Answer 2

We do have the 22 mm version of the Replacement 20 mm Lug Nut for Wheel Master Wheel Liner #WMRMT9063. The #WM9062 is what you're looking for. Also yes, the Replacement Wheel Master Lug Nut Cover #WMRMT9061 will fit the 22 mm so you…

view full answer...

Answer 3

If you can provide me with the part number of your wheel cover I could then confirm the correct replacement parts that you need. For the lug nuts that hold on the wheel covers we have part #WMRMT9063 which is 20mm and then for the cover for the lug…

view full answer...

Answer 4

The most direct replacement would be the model GC10A-4E, this is not a heater currently available. However, the better, in my opinion, replacement water heater would be a tankless system. The Furrion RV Tankless Water Heater, #FR98SR, has…

view full answer...

Answer 5

To install ball plate #RP58062 you will need to drill 4 holes using an 11/32 (.343) drill bit for 1/8" (.125) or thicker trailer tongue material, or a 9/32" (.281) drill bit for thinner material. Then you will line up the plate with…

view full answer...

Answer 6

I looked up the lug nut size of the 2005 Workhorse W22 chassis that you have and since it has 33 mm lug nuts the lug covers you'd need are the part #PXSP33. We don't have this size lug nut though.

view full answer...

Answer 7

I have a solution for you but there is not a direct replacement for your old Atwood unit. Instead, you can use the 2-Wire RV Propane Gas and Carbon Monoxide Detector - 12 Volt - White #RS34FR to replace your old Atwood carbon monoxide detector, but…

view full answer...

Answer 8

In order to determine if #WMRMT9061 will work for your 2017 Ford F-150, you'll need to measure or remember what size socket you use to remove your lug nuts is. If you measured 33mm, then #WM9005-6 will work for you. If you measured 1-1/16",…

view full answer...

Answer 9

We do have the stainless steel lug covers available in a few sizes. We do not have a way to look up exactly what lug nut size your 2016 Winnebago Sunstar LX uses, so we will need you to verify that information. The stainless lug covers are available…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

How Tall is Replacement Wheel Master Lug Nut Cover # WMRMT9061

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching