Does Placement Matter in Regards to the Replacement Legs for the Lippert Ground Control 3.0

Question

Question:

Whats the difference between left and right rear legs they look the same both go up and down but yet price is different ??????

asked by: Gordon

0

Expert Reply:

The difference between the Replacement Left Rear Leg for Lippert Components Ground Control 3.0 part # LC305339 and the Replacement Right Rear Leg for Lippert Components Ground Control 3.0 part # LC344792 is the side of the jack that the mounting bracket attaches to. The jacks are the same but the mounting bracket is welded to the side which will then determine which side of the trailer it will need to be installed on. The jacks cannot be flipped between sides. They are each priced according to market value and will fluctuate accordingly.

They are designed to work with the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part # LC358590 and the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part # LC675817.

expert reply by: Conner L

0

Answer 1

The Ground Control jacks for travel trailers are different as they are a C-jack instead of a vertical lift. I recommend using the Replacement C-Jack for Lippert Components Electric Ground Control TT #LC404488 for that application instead of combining…

view full answer...

Answer 2

I attached a dimension picture I got from Lippert for the Replacement I-Beam Jack Bracket #LC349975 that you referenced.

view full answer...

Answer 3

Yes. If you were to wire the power and ground wires on the Replacement Legs #LC305339 and #LC344792 to a switch similar to the Replacement Power Switch #LC144214 you would be able to use them independently of a Lippert Ground Control system #LC358590…

view full answer...

Answer 4

I do have a solution for you, but unfortunately there are no replacement legs for your stabilizer jack 113407 and you will need to replace the whole unit. I confirmed this with my contact at Lippert. The correct replacement for your jack is the…

view full answer...

Answer 5

The overall height of the mounting plate of the Replacement I-Beam Jack Bracket for Lippert Ground Control #LC349975 is 13 inches.

view full answer...

Answer 6

Yes it does, what you will need are 1/2"-20 self-tapping bolts in order to install the bracket you asked about: - Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0 #LC349975

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

I went ahead and pulled this Replacement I-Beam Jack Bracket #LC349975 from our warehouse to measure. I have attached the dimensions below. Hope this Helps.

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 12

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...