Trailer Hitch And Wiring to Tow a Trailer With a 2010 Honda Odyssey

Question

Question:

I am a single mom from Utah that wants to take her children camping. I have a 2010 Honda Odyssey what kind of tow hitch will I need to install to my Odyssey please?

asked by: Suzanne V

0

Expert Reply:

We have both the hitch and wiring you need to tow with your 2010 Honda Odyssey.

Starting with a trailer hitch you'll need the Draw-Tite # 75270 and to add a 4-flat to your Odyssey so you can power your trailer's lights I recommend the Hopkins # HM11143115.

expert reply by: Kyle S

0

Answer 1

The ideal height will actually have to do with how tall the coupler of the trailer is from the ground. The Draw-Tite #76020 will sit at 13 1/2 inches from the ground to the top of the hitch when installed on a 2016 Mazda CX-9. From what I could…

view full answer...

Answer 2

Yes, the Bearing Kit, L44649 Inner/Outer Bearings, 10-60 Seal part #BK1-150 is correct for a Scamp 13 Trailer with Lippert 2,200 lb Axle.

view full answer...

Answer 3

The SumoSprings Coil Helper Spring kits #CSS-1168 and #CSS-1168R that you found on our site are actually the same product. The R designation that we use on the one kit refers to an application on the REAR coil springs on a 2006 Honda Odyssey like…

view full answer...

Answer 4

Since your truck has a manual transmission, it's unlikely that what you're smelling is the transmission burning. What you're smelling is much more likely to be your clutch going out. Manual transmissions generally…

view full answer...

Answer 5

To determine the axle size you will need there are some measurements needed. First, if you are replacing the axle then you can measure the one you have. Measure from the center of one spring seat to the center of the other spring seat. Then measure…

view full answer...

Answer 6

Using the push rods of the Derale Dyno-Cool Tube-Fin Transmission Cooler Kit #D12903 will not cause any damage to the condenser of your vehicle. The fins are designed to be slightly bent and not be permanently damaged. Also, no amount of damage to…

view full answer...

Answer 7

In the USA a tandem axle utility trailer with a gross vehicle weight rating (GVWR) of 7500-lbs should have brakes installed. Any trailer over 3000-lbs must have brakes on all wheels in most states, but laws do vary. Some states require braked axles…

view full answer...

Answer 8

There are a few components you need to haul your 2021 Jayco Jay Flight SLX 7 154BH with your 2016 Honda Odyssey. Since you already have the Draw-Tite Hitch, part #75270, and the T-One Harness, part #118521, the remaining necessary components are: a…

view full answer...

Answer 9

The general rule of thumb is that if the trailer comes with brakes then you need to add a brake controller in your tow vehicle (2010 Honda Odyssey) to utilize them. Another great source to reference about this is your owner's manual. When I…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

When we installed the Draw Tite hitch part #75270 on a 2011 Honda Odyssey the distance from the ground to the top of the hitch opening was 12 inches. When we installed #76025 the distance was 12-1/2 inches. The Curt #C13068 was 12-3/4 inches. Draw…

view full answer...

Answer 12

Honda states in the owner's manual for your Odyssey that the vehicle should be equipped with a power steering and a transmission cooler before using it for towing. Whether you choose to follow that advice is entirely up to you, but opting for…

view full answer...

Trailer Hitch And Wiring to Tow a Trailer With a 2010 Honda Odyssey

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching