Replacement Post Recommendation for CE Smith Bunk-Style Guide-Ons for Boat Trailers

Question

Question:

Looking for a relacement post that hold the flat bunk

asked by: MIke

0

Expert Reply:

Sounds like you have a set of boat trailer guide ons and are looking for a replacement post. I'd have to know which system you have though to know for certain.

If you have the part # CE27660 then the correct replacement post would be the part # CE27609PG.

expert reply by: Jameson C

0

Answer 1

The CE Smith Bunk-Style Guide-Ons you mentioned, part #CE27660 will work on trailer frames up to 3 inches wide by 4-1/4 inches tall, therefore they would work just fine with your trailer. The attachment brackets allow you to fine-tune the width of…

view full answer...

Answer 2

I went out to the warehouse to measure the horizontal part of CE Smith Bunk-Style Guide-Ons #CE27660. The length is 12 inches so if 2 inches of frame are covering up part of that then that leaves 10 inches that will stick in towards the center of…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need…

view full answer...

Answer 5

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 6

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights…

view full answer...

Answer 8

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have…

view full answer...

Answer 9

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

The squeaking noise on your trailer is probably coming from the joints in the suspension creating metal to metal friction. So, unless your original Equa-Flex Cusioned Equalizers are damaged or corroded, what will make the biggest difference is to…

view full answer...

Replacement Post Recommendation for CE Smith Bunk-Style Guide-Ons for Boat Trailers

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching