Will Double RV Waste Valves # T18 Fit 1988 Thor Citation 35 Camper

Question

Question:

I just purchased a 1988 Thor Citation 35 camper for my fishing camp. Attached are the pics of my current valve, which is broke. Just to confirm, it looks like the #T18 is the proper replacement valve....correct? Thank you!!

asked by: Stephen Y

1

Helpful Expert Reply:

From the pictures that you sent in the Double RV Waste Valves # T18, which has a 3" hib and a 1-1/2" hub will be a direct replacement for your 1988 Thor Citation 35 camper.

A review video has been linked for you to check out as well.

expert reply by: Jon G

1

click to enlarge

Answer 1

The Double RV Waste Valves #T18A has a 1-1/2" spigot so you'd have to also pick up a coupling #344633001 in order to attach it to the existing pipe. Instead I recommend the Double RV Waste Valves #T18, which comes with hub fittings so you…

view full answer...

Answer 2

Thanks for the picture of what you have based on that you are in need of the Double RV Waste Valves - Sewer Wye #T38C.

view full answer...

Answer 3

Based on the picture you sent in you'd need a sewer tee and not a wye since the angle of the two pipes is 90 degrees relative to each other in your picture. For that we have the part #T18A which would match the orientation of your pipes. I…

view full answer...

Answer 4

The Double RV Waste Valves #T18A has the following dimensions: From the edge of the 3" hub to the bayonet: 7" From the 3" hub flange to the bayonet: 5-1/2" From the edge of the 3" hub to the center line of the 1-1/2"…

view full answer...

Answer 5

Thanks for the photo and based on that we do have a replacement that will work for you although you are going to need to know what your gray water pipe and black water pipe connections are - either spigot or hub - which I'll explain but you are…

view full answer...

Answer 6

I attached a picture I got from Valterra that shows the overall dimensions of the Double RV Waste Valves #T68 for you to check out.

view full answer...

Answer 7

I went out to the warehouse to take a measurement of the 3" diameter pipe on the Double RV Waste Valves #T38C and found that without the cap it measured 5" in length, as you can see in the accompanying photo I've added for you. I have…

view full answer...

Answer 8

You should be able to tell which Valterra Double RV Waste Valves you need by inspecting your current connection points. The one end with the lugs on it is the same on all 3 parts so you simply need to determine if you need hubs, spigots, or a…

view full answer...

Answer 9

No, the Bristol Double RV Waste Valves #34466ND13AAR would not match what you have pictured, but you would be able to swap out what you have with the Double RV Waste Valves #T38C.

view full answer...

Answer 10

Using a spacer kit like the #T68MR to allow one side of the truck's suspension to engage sooner will give you more support on that side but since it's hard to say if that will happen to be the sweet spot you are looking for in terms of…

view full answer...

Answer 11

From the picture you provided, it does look like the Double RV Waste Valves - Sewer Wye - Rotating - 3" Spigot and 1-1/2" Spigot #TR38B will be the correct fit for you. However, I will say it is a good idea to measure the 2 pipes going into…

view full answer...

Answer 12

Thank you for the pictures! Based on the pictures you provided of your broken RV Sewer Valve I recommend the Double RV Waste Valves #T68C which has the same heel inlet as your broken valve. You will also need Valterra ABS Solvent Cement #A05-0303 to…

view full answer...

Will Double RV Waste Valves # T18 Fit 1988 Thor Citation 35 Camper

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching