What is Meant by Left and Right Side for Trailer Brake Assemblies

Question

Question:

which end of the trailer are you standing at for determination?

asked by: Chuck

0

Expert Reply:

Left = driver's side
Right = passenger's side

We generally do not use the terms driver's or passenger's side since trailers don't have drivers, etc. For brake set # T4489600-500 the shorter shoes will face towards the front of the trailer.

expert reply by: Michael H

0

Answer 1

To bleed the Titan Zinc-Plated Brake Actuator w/ Drop part #T4750600 using the lockout arm isn't the way to go. What I prefer to do is use a larger 5 foot piece of 2x4 you will place this up against the ball coupler and loop the safety chains…

view full answer...

Answer 2

Most trailer wiring that runs to incandescent trailer lights is 16 gauge which would be a little less than what we would like, However for LED lighting 16 or 18 gauge is fine. To make your project easier I would use the Optronics #A35W42B wiring…

view full answer...

Answer 3

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

What is Meant by Left and Right Side for Trailer Brake Assemblies

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching