Brake Controller and Install Harness Recommendation for 2016 Jayco Alante 31V

Question

Question:

where is the factory port for trailer brake wires ? also there is a factory plug/harness that came with, is this usable ? if so where does it plug into ? i cannot find a port for this under the dash.

asked by: Gordon S

0

Expert Reply:

Your 2016 Jayco Alante 31V is built on a Ford F-53 chassis so for a brake controller install harness the correct part number is # 3034-P. The brake controller connector is located on the left side of the steering column support, as shown in the provided photo.

expert reply by: Jameson C

0

click to enlarge

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

You do have the option to utilize the air brakes on your 2023 Freightliner Cascadia to control electric trailer brakes using the Hayes Air Actuated Trailer Brake Controller, part #HA100400C. However, we mostly recommend just using an electric brake…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

I do have a solution for your 2024 Kia Telluride that has the LED taillights that does allow it to have both a 4-way and 7-way plus install a brake controller but it is not with the #TK74CR which does not work for you based on the LED taillights.…

view full answer...

Answer 9

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 10

A factory 7-way trailer connector isn't all you need to power a trailer's electric brakes. You still need a brake controller. Some Ford F-150s are equipped with a factory integrated brake controller, which you may have. If your 2012 Ford…

view full answer...

Answer 11

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 12

Sure thing, I will go ahead and list out what you need for your 2023 Kia Sportage to add a 7-way for a brake controller so you can tow with the Curt Trailer Hitch Receiver #C94WR: - T-Connector Vehicle Wiring Harness with 4-Way Flat Trailer Connector…

view full answer...