Parts for Thule Tracker TK1 Rail Foot Pack

Question

Question:

Im missing All 4 base for my TK1 part number 8535112, What hardware do I require to mount to the rails on my rails.

asked by: Dan

0

Expert Reply:

For your TK1 system, you will want the Replacement FootBase Thule Tracker Roof Rack # 753-2149. Depending on the rails you have, you will either want the track nut # 853-2106 or # 853-5147.

Then you will want bolt # 924-0617-15 with key # 853-2430-02. The washers needed are black washer # 951061254 (2 needed per base, 8 total) and yellow washer # 951-0613-12 (2 needed per base, 8 total).

The Tracker II Feet are no longer available but it sounds like you already have them so these parts will work for you.

expert reply by: Jason S

0

click to enlarge

Answer 1

I pulled this from our warehouse and it was a lot smaller than I originally thought. In the attached picture I have all of the dimensions you requested noted. To give you a quick overview of the dimensions: Thickness - .16 inches Long Sides - .993…

view full answer...

Answer 2

The Track nut #853-2106 that you referenced will also work on the TK1 roof rack fit kit so it would be exactly what you would need.

view full answer...

Answer 3

In sort of a backwards way we know that the part #753-2149 does fit the feet you have since we had a customer with a TK1 tell us that on the bottom of the foot they say your same part number of 8535122

view full answer...

Answer 4

Replacement Track Nut for Thule Tracker II Half Foot Pack or Tracker Fit Kits TK6, TK8, TK9 #853-2106 is made to be used with Replacement M6 x 17 mm Bolt for Thule Tracker II Half Foot Pack or Fit Kits #924-0617-15. The threading on both parts is…

view full answer...

Answer 5

The Replacement Track Nut for Thule Tracker II Half Foot Pack or Tracker Fit Kits TK6, TK8, TK9 #853-2106 will fit in your tracks and were designed to secure the Tracker II feet to the rail using bolt #924-0617-15. Without knowing what towers you…

view full answer...

Answer 6

Both track nuts you mentioned of #853-5147 and #853-2106 have M6 thread size.

view full answer...

Answer 7

The track nut part #853-2106 is M6 and is sold individually.

view full answer...

Answer 8

It looks like we have everything you would need except for one of the washers (washer 951061312). I have listed the parts out below. TK1 Base - Part #753-2149 Cover -- Part #853-7084 M6 x 17 mm Bolt -- Part #924-0617-15 M6 Washer - Part #951061254…

view full answer...

Answer 9

Yes, the track nut used for the Thule Fit Kit #THKIT3101 is the same one that was used for the discontinued TK1. If you are just needing to replace the track nut then we have it available as part #853-2106 on our site.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 12

Gen-Y's calculation for pin weight is a safe guess, but isn't the most accurate so the only way you'll get the correct capacity Gen-Y 5th Wheel Pin Box is to fully load the trailer and go to a commercial scale to measure the pin weight.…

view full answer...

Parts for Thule Tracker TK1 Rail Foot Pack

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching