Recommended Custom Wedge for Curt e16 5th Wheel Hitch and Lippert Turning Point Pin Box

Question

Question:

I have a Curt e16 hitch and Lippert Turning Point pin box on a Grand Design 290BH 150 series. what wedge for rotating pin box ?

asked by: Steve

0

Expert Reply:

The correct custom wedge for your Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs # C16115 is the # C16991. This allows you to use the hitch with a sidewinder.

expert reply by: Chris R

0

Answer 1

Since your trailer has the bracket #FRCBRKT-BL that would mean your trailer has the Furrion pre-wiring which is very common for newer RVs. The part #FOS43TASF is a fit for this and would be a really easy install. This gives you a monitor with a 4.3…

view full answer...

Answer 2

Based on the sharkfin camera mount in the picture you provided I can tell you that your 2021 Amerilite 189DD was prewired for Furrion cameras #FRCBRKT-BL. Because of this you won't be able to find an adapter but can cut the plug-in off of the…

view full answer...

Answer 3

I wish that option would work, but unfortunately the Furrion Prewiring on your 2021 Grand Design will only work with a Furrion system like the Furrion Vision S Wireless RV Backup Camera System w/ Night Vision - Rear Mount - 5" Screen #FOS05…

view full answer...

Answer 4

I spoke with my contact at Curt who said that the A20 5th Wheel Hitch #C16140 is compatible with the Trailair Rota-Flex 5th Wheel Pin Box without any additional components. He did say that they have heard of instances where the rubber pad on the…

view full answer...

Answer 5

The Q series of Curt fifth wheel hitches are considered to be the nicer Curt fifth wheel hitch when compared to the E16 hitch. Biggest difference being the jaw design. The E16 #16516 uses a slide bar jaw design that allows quite a bit more movement…

view full answer...

Answer 6

The 5th Airborne Premium 5th Wheel Air Ride King Pin w/ Sidewinder and Turret #RP61412 is the correct replacement for you Lippert 1621 that you have installed on you RV, but you have to use a standard fifth wheel hitch with this like the Reese…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

The Furrion camera system we have is a closed system and would not be compatible with the in-dash display so you would need to purchase GM's camera system to be able to connect to your display instead of having another monitor. If you do end up…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...