Where is the Brake Controller Port on a 2015 Jeep Grand Cherokee

Question

Question:

I purchased the Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers Part Numbers: 90195,TK93VR for my 2015 Jeep Grand Cherokee. When looking at the wire harness for TK93VR, it does not appear to be the correct fit for the harness beneath my dash see pic. Am I not seeing things correctly, or do I need a special adapter to connect the Tekonsha P3 to my Jeep? Thank you

asked by: Derek

0

Expert Reply:

The picture you attached is the OBDII port and will not connect with the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers part # TK93VR. The port that you will need to find will match the grey connector on the adapter harness. If you take a look at the 3:00 mark in the attached review video, the location of the plug you will need to access will be shown.

expert reply by: Conner L

0

click to enlarge

Answer 1

The Tekonsha Plug-In Wiring Adapter item #TK93VR is the same harness as the 3045-P. Item #TK93VR is the updated model number. Both will allow you to install a Tekonsha Brake Controller like the Tekonsha P3 item #90195 in your 2019 Jeep Grand Cherokee…

view full answer...

Answer 2

Yes, in order to install the Tekonsha Prodigy P3 Trailer Brake Controller part #90195 on a 2015 Jeep Grand Cherokee you can use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers part #TK93VR for a plug-in-play installation. I have…

view full answer...

Answer 3

I'll begin with the assumption that you have a 2015 Jeep 'Cherokee Latitude, as the Renegade and Compass Latitude weren't equipped with the optional factory 7-way. The brake controller connector is located behind the black cover down near…

view full answer...

Answer 4

There is a folding double step that has the same 24-1/4 inch wide x 8-1/4 inch dimensions as the Lippert Manual Pull-Out Step for RVs - Single #LC432678; the step you are looking for is the following: - Lippert Manual Pull-Out Step for RVs - Double…

view full answer...

Answer 5

The brake controller install harness on your 2022 Jeep Grand Cherokee 4xe is under the dash, to the left of the steering column, taped to another harness near the emergency brake pedal. The Tekonsha brake controllers like the Prodigy P3 part #90195…

view full answer...

Answer 6

I looked up the trailer connector wiring diagram for a 2007 Ford F-250 which should be the same as a Ford F-350 and found the 7-way trailer connector to contain the following wires: Orange = 12 Volt Power White = Ground Black/Green = Reverse Blue =…

view full answer...

Answer 7

Yes, you are looking for part number, #90195 for the Tekonsha Prodigy P3 Trailer Brake Controller and need the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers, #TK93VR too. This adapter plugs into the 4-pin connector on your…

view full answer...

Answer 8

Hi Andrei; yep, you're 100 percent right, you should use the 30 amp breaker. That's why for the installation kit I recommend using the Universal Installation Kit for Trailer Brake Controller #ETBC7. The #ETBC7 comes with multiple breakers,…

view full answer...

Answer 9

I have a solution for you, but the #LC379145 is not the correct motor replacement for a PowerGear 903209000. According to my tech contact at Lippert, the correct replacement motor is the Replacement Lippert Components 5:1 Gearbox With Motor for RV…

view full answer...

Answer 10

Your National seal 413470 has an outer diameter of 3.376 inches and an inner diameter of 2.125 inches. For a replacement we have #GS-2125DL for one seal or #RG06-090 for a pair. These are all double lip seals.

view full answer...

Answer 11

For your 2015 Jeep Grand Cherokee I recommend the P3 brake controller, #90195. This is a proportional controller that will apply the trailer brakes in proportion to how much the Jeep is braking. this is the safest way to stop and it reduces wear and…

view full answer...