How to Determine the Correct Replacement Bearings for an EZ Loader Boat Trailer

Question

Question:

Hi I have an ez load trailer, single axel that has a sea pro 190 boat on it. 18.5foot boat. 14inch wheels. Would like to know the correct bearings for them... Thanks...

asked by: Chris B

0

Expert Reply:

EZ Loader makes both custom and "universal" trailers so in order to determine which bearings are on a given trailer you can either pull a hub and get the inner and outer bearing numbers off of the sides of the bearings or measure the spindle with digital calipers such as # PTW80157. I have included a video and a picture that will help.

expert reply by: Michael H

0

click to enlarge

Answer 1

Bearing Kit #BK3-100 consists of bearings 15123 and 25580, matching races, grease seal and cotter pin. This kit is intended for a 6K axle. The same component parts are found in Lippert bearing kit 333950, also rated for a 6K axle. Two helpful…

view full answer...

Answer 2

I'd be happy to get you the correct bearing for your trailer with Dexter axles, and while the 8-219 narrows things down a bit there's still a two options so you'll need to take one measurement to confirm which kit is right for you. The…

view full answer...

Answer 3

From what I was able to determine, your CR 21352 grease seal is a Chicago Rawhide 21352 and should be a double lipped seal with a 2.125" ID and 3.376" OD. To replace a seal of that size you'll want to use the #GS-2125DL, which has the…

view full answer...

Answer 4

Without know exactly what weight capacity of double axles you have on your 2021 No Boundaries Forest River, I can confirm that the kit #BK3-210 that you referenced will only fits 7k axles. One way you can confirm whether you have 7k axles on your…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 12

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...