Where Do Safety Cables Attach on Roadmaster EZ Base Plate Kit for 2007 Mazda MX-5

Question

Question:

Im looking to put an EZ2 on my 2007 Mazda Miata and dont see where the safety cabes attach to the base plate. Is there something else I need, or am I missing something on the base plate?

asked by: Brian

0

Expert Reply:

I attached a picture that shows where to attach the safety cables when installing the Roadmaster EZ Base Plate kit part # 52728-1. Here's the text too though.

Attach the ends of the 8” safety cables to the front holes in the cable
mounting tabs located on the inside of the receiver braces with the included
cable connectors (Fig.X). Connect the other end to the tow vehicle's safety
cables and tow bar.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Roadmaster EZ Base Plate Kit #52728-1 does require you to use a crossbar with your Roadmaster Falcon All Terrain, Non-Binding Tow Bar #RM-522. You will need the Replacement Quick Disconnect Crossbar Assembly #910021-00 if you do not currently…

view full answer...

Answer 2

I attached a diagram for the 3 wire install of the Roadmaster kit part #154-792-118158 which can be used as a guide for installing the part #TR118821 as well.

view full answer...

Answer 3

When flat towing a vehicle you cannot reverse the setup at all. You'd have to disconnect the towed vehicle and reverse it by itself before reversing the motorhome. If you attempted to do this you'd most likely damage the tow bar and vehicle.…

view full answer...

Answer 4

The Hopkins Custom Tail Light Wiring Kit for Towed Vehicles, #HM56009 is not a confirmed fit for a 2021 model Ford F-150. For your vehicle I suggest the Tow Ready Tail Light Isolating Diode System with 4-Pole Connector #TR118821.

view full answer...

Answer 5

Yes, the Roadmaster EZ Base Plate Kit - Removable Arms #52728-1 is a confirmed fit for your 2006 Mazda Miata

view full answer...

Answer 6

The part you are looking for as a replacement piece for your RoadMaster Falcon Tow Bar #RM-522 is the RoadMaster Base Bar #RM-067. It attaches to the quick disconnects on your vehicle. If you also need the Quick Disconnects, they are part #RM-222.

view full answer...

Answer 7

The Roadmaster EZ Base Plate Kit - Removable Arms #52728-1 you were looking at for your 2011 Mazda MX-5 Miata weights in at 45lbs with the removeable arms, and while Roadmaster did not have an exact weight of the arms they did mention they are…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...