Can Hitch be Installed on 2003 Nissan Pathfinder With Rear Bumper Guard?

Question

Question:

Hello - can you tell me if this product can be installed in a 2003 Nissan Pathfinder SE - 4X4 that has a rear bumper guard? Please see attached pictures.

asked by: Lou

0

Expert Reply:

The Curt Trailer Hitch Receiver # C13156 would not be able to fit your 2003 Nissan Pathfinder with your rear bumper guard installed. The guard would need to be removed in order for this hitch to fit on your vehicle.

expert reply by: Kyle S

0

click to enlarge

Answer 1

The correct size tread tap that would be needed for the weld nuts on a 2017 Toyota RAV4 when installing the Curt Trailer Hitch Receiver part #C13149 is 12 mm x 1.25".

view full answer...

Answer 2

Most Vehicles and hitches have their own specific hardware to insure proper fit and towing capacity. Our #C13149 hitch includes a hardware kit and installation guide. I attached a video on the installation for your convenience. The hardware specs can…

view full answer...

Answer 3

Are you trying to replace the awning arms? Or just a portion of the arms?

view full answer...

Answer 4

The two hitches you mentioned are very similar in size and installation. When comparing round and square hitches, round tube hitches are usually sleeker compared to square hitches. Any hitch for your Pathfinder will stick out past the bumper. I…

view full answer...

Answer 5

I took a look at what Lippert and ourselves offer as replacements for the Lippert Solera awning, and the outer cover for the arm that you mentioned is actually offered as a replacement part. Instead, to replace that piece, you're going to have to…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Can Hitch be Installed on 2003 Nissan Pathfinder With Rear Bumper Guard?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching