What is the Size of the Installation Bolts on the Yakima Kickstand for Rack and Roll Trailers

Question

Question:

Can you please tell what is the size of the bolt and nut that tightens the Yakima Kickstand on to the trailer tounge? I have lost one. thank you...

asked by: Dean M

0

Expert Reply:

I spoke with my contact at Yakima and she informed me that the bolts that hold this Yakima Kickstand # Y085115 are 5 mm in diameter and 38 mm long. She also informed me that these bolts are coated in yellow zinc.

I attached a review for the # Y08115 for you to check out also.

expert reply by: Jameson C

0

Answer 1

The Yakima Rack and Roll Trailer Kickstand, part #Y08115 is designed to fit 2x2 inch tubing. Keep in mind that the trailer that this item is designed for has 200 lb capacity, so it is not designed for heavy duty use.

view full answer...

Answer 2

Yes, your 14 foot Hobie pedal kayak can absolutely be carried with the Yakima trailer, which is the following part number: - Yakima Rack and Roll Trailer #Y08107 There are no special details regarding the Rack and Roll #Y08107, as it is designed to…

view full answer...

Answer 3

The Yakima Rack and Roll trailer part #Y08106 doesn't have any safe jacking points on it so if you were in need of changing the spare you'd have to remove the kayak and raise the trailer by hand.

view full answer...

Answer 4

My contact at Yakima advised that they do not recommend modifying their Rack and Roll Trailer #Y08106. Also, please note that if you did shorten the tongue length it will be somewhat tougher to back up the trailer since every steering change in the…

view full answer...

Answer 5

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 6

The CE Smith Multi Sport Plus Boat and Kayak Trailer w/ Bunks #CE48870 that you referenced was designed to be used with boats that are up to 14 feet in length like what you have now. I attached a picture that shows the range of where the winch…

view full answer...

Answer 7

I do have an option but Glo-Brite is no longer in business so you won't be able to get any replacement parts for these lights such as lenses. The only option you have would be a full replacement for which the most similar option we offer is the…

view full answer...

Answer 8

It's good to know the Redline 2-Way Pop-Up Roof Vent #9106-2756 is finally back in style! :) There really isn't a "wrong" way to install it on a trailer but if it's raining you'd most likely want to keep it closed, or at the…

view full answer...

Answer 9

The Champion 9,000-Watt Dual Fuel Inverter Generators w/ Parallel Kit, #CH49FR has the same power output specs regardless of type fuel used. There is a starting (surge) power output of 4,500 watts/37.50 amps with a running power output of 3,500…

view full answer...

Answer 10

The Champion 9,000-Watt Dual Fuel Inverter Generators w/ Parallel Kit, #CH49FR have a push button electric start and operate from either propane or a minimum 87 octane rating gasoline for their fuel source. Run time is up to 14 hours on gas and as…

view full answer...

Answer 11

You actually do not want the weight of the load on a trailer to balance perfectly on either side of the axle. You want more weight forward so that the trailer doesn't sway. What you'll want is 10-15 percent of the total trailer weight as…

view full answer...

Answer 12

We have the CE Smith boat trailer part #CE48810 which is designed for small boats like your 12.5 foot Flycraft inflatable boat. I attached a picture that shows a similar boat loaded on this trailer as well.

view full answer...