Weight of the Epicord RV Power Cord with Handle # 277-000155

Question

Question:

How much does the Epicord 50 Amp 36foot power cord Item # 277-000155 weigh and how small will it coil?? Thanks!

asked by: Cathy S

0

Expert Reply:

The Mighty Cord RV Power Cord with Handle # A10-5036EDBK that you referenced weighs about 24 lbs.

I am not sure how small it will coil though as that is not a standard feature that is measured on power cords like this. I can say that you need to make sure not to force the cord when coiling it for storage as that could very well cause some damage.

Attached is a review video for you to check out.

expert reply by: Jon G

0

Answer 1

The recommended air pressure for the Lippert Center Point by Trailair Air-Ride Suspension Upgrade #LC1565391 is going to be 5 PSI for every 1,000 pounds. So for your 27,000 lb. trailer you would be looking at 135 PSI. The #LC1565391 only goes up to…

view full answer...

Answer 2

The puck feet on the Gen-Y Hitch Gooseneck Trailer Hitch for Dodge Ram OEM Puck Systems #GY83XR is just to help stabilize the ball mount and does not lock into place in the puck. The locking mechanism on top will lock the shank into the gooseneck…

view full answer...

Answer 3

The correct replacement surge module for the Power Watchdog Surge Protector with Bluetooth and Emergency Shut Down #HU27FR is the #HU58FR. I attached an installation video below for your reference.

view full answer...

Answer 4

For your 50 amp system, you will want the Camco RV Power Defender Voltage Monitor - 50 Amp #CAM55306. This voltage monitor disconnects when dangerous voltage levels are detected and then reconnects when it stabilizes. This is much better than the…

view full answer...

Answer 5

The Mighty Cord RV Power Cord #A10-5036EDBK lists the wire gauges as 6 gauge (3 wire) and 8 gauge (1 wire). The 6 gauge wire is used for the two power legs and negative, and is capable of handling 55 amps. The 8 gauge wire is used for the ground.

view full answer...

Answer 6

Based on the question you're asking about I'm assuming you have a Dometic setup right now. The 6-pin wiring harness on the #ACM135 will allow you to use the other components from your existing Dometic setup. I don't know exactly what…

view full answer...

Answer 7

The sleeve or sheathing is part of the cord, not the plug so even if you were to just replace the plug using something like the Mighty Cord Replacement Hardwire RV Plug part #A10-P50VP you would still have exposed wires. Therefore, it would be best…

view full answer...

Answer 8

The Progressive Dynamics Transfer Switch - Metal Case - 50 Amp - 120V/240V #PD52 (Alternatively PD52V) and the PD52DCS/PD52DCSV are both part of the PD52 series but there are some differences. Both share the same voltage rating and current ratings.…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 11

Hey Joe, yes the Lippert stabilizer jack part #LC298707 does fit your Grand Design Transcend 245RL but it is sold individually so if you wanted a set for the front and the rear you would need to order a quantity of two.

view full answer...

Answer 12

Hey Frankie, The bracket for the Timbren Suspension Enhancement System #TFR250SDJ has a locknut in it that makes it feel like the bolt (part #4) is fully tightened when it's not. Their techs have stated that you just have to push past this point…

view full answer...

Weight of the Epicord RV Power Cord with Handle # 277-000155

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching