How to Install the TorkLift GlowStep Revolution in a Grand Design Reflection 337RLS

Question

Question:

I WANT TO BUY THE TOLKLIFT GLOW STEP REVOLUTION, BUT WHEN IVE LOOKED AT THE TORKLIFT SITE THEY SAY MY GRAND DESIGN REFLECTION 337RLS REQUIRES A CUSTOM INSTALLATION. CAN YOU ASSIST ME IN WHAT ADDITIONAL PARTS I NEED TO MAKE THIS INSTALLATION?

asked by: STEVE

0

Expert Reply:

I assume you have a MorRyde or Lippert step currently installed in your Grand Design Reflection 337RLS, which is what would require the custom work you referred to.

I spoke with a representative of TorkLift, who said you can install the TorkLift GlowStep Revolution Scissor Steps w/ Landing Gear # TLA8004 in your Grand Design Reflection 337RLS and the custom work would mean that you would first have to unscrew and remove your step, then look on the underside of the threshold where the step was. If there are still brackets there you would use those to mount the GlowStep Revolution. If the brackets were NOT there you would simply need to use the GlowStep Revolution Vertical Stud Adapter Bracket # TLA8022.

The only other thing you would need to look for on the underside of that threshold is a cutout where your OEM steps mounted. If that cutout was not there, you would simply need to make it yourself.

I have attached a link to the installation instructions of these steps for you to take a look at.

expert reply by: Kyle S

0

Answer 1

You won't be able to use two steps at the same time, so you will need to remove the current step to install your Glow Step. You can save that step and reinstall on that trailer once you get a newer trailer to put your GlowStep on. From your…

view full answer...

Answer 2

It sounds like you're asking if the TorkLift GlowStep Revolution Uprising Steps w/ Booster Step #TLA9005 will work where your previous Morryde steps were. If this is what you're asking, you'll just have to take a couple of measurements to…

view full answer...

Answer 3

In order for the bracket of the TorkLift GlowStep Revolution Uprising Steps #TLA9005 that you referenced to fit the door sill the height does need to be between 5/8 inch and 3/4 inch to allow the door to still close over it. So if you can use a…

view full answer...

Answer 4

The Torklift #TLA8003 (3 Steps) will fit for your trailer. These are intended for a mounting bracket measuring 27-1/2" and an entry height of 25-1/2" to 36". Alternatively, the Torklift #TLA8004 (4 Steps) is designed for an entry…

view full answer...

Answer 5

With the interior stairs being in the way like they are your only option is to go with an undermounted step like the TorkLift GlowStep Revolution Scissor Steps w/ Landing Gear #TLA8003 I recommended before. To make fold-down steps work in your 2019…

view full answer...

Answer 6

The GlowStep Revolution vertical stud adapter bracket #TLA8022 is made specifically for trailers without vertical brackets that extend out perpendicular from the trailer's frame or "predrilled step frame outrigger mounting brackets" to…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...