Companion Base Recommendation for Ram Factory Fifth Wheel Rail Kit

Question

Question:

2015 RAM 3500 FACTORY FIFTH WHEEL PREP Can I just buy the base from you? I have a sliding companion now, that goes into the gooseneck. but Im looking at a new truck with factory puck setup.

asked by: Matt

0

Expert Reply:

We do have the B and W Companion hitch bases for the Ram factory fifth wheel rail kits. For the slider base you'd want the part # BWRVB3670 and for the fixed hitch base you'd want the part # BWRVB3600.

expert reply by: Jameson C

0

Answer 1

The spacing for the pucks on the Replacement Base for B&W Companion OEM 5th Wheel Trailer Hitch for Ram #BWRVB3600 is 39-1/8" L x 30-1/2" W from center to center of the pucks so you could expect and overall length of approximately…

view full answer...

Answer 2

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Beds shorter than 8 foot do commonly need a slider hitch David, but a lot of modern fifth wheel trailers are now made with tapered noses to help and in a lot of cases a slider isn't required. So if the trailer you plan to tow has a tapered nose…

view full answer...

Answer 7

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 8

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 9

You will want the hitch to be set at the height that 1) allows the trailer to be level, and 2) allows you a minimum of 6 inches between the bottom of the trailer loft and the top of the bed rails. The fifth wheel hitches offer several inches of up…

view full answer...

Answer 10

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Answer 11

The Curt A25 5th Wheel Trailer Hitch for Ram Towing Prep Package #C16046 will work well with the Roto-Flex pin box. The combination will be a good match for you and this hitch with the specific connection to the factory prep package pucks will make…

view full answer...

Answer 12

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Companion Base Recommendation for Ram Factory Fifth Wheel Rail Kit

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching