How Do I Get a VIN Number For My New Trailer?

Question

Question:

Hi. I brand new trailer end is no vin number. What I can do in this case? Thanks

asked by: Andrei

1

Helpful Expert Reply:

When you have a trailer with no VIN number, you will need to contact your State Highway Patrol to have them inspect your trailer and issue you a VIN so you can properly register it.

expert reply by: Jason S

1

click to enlarge

Answer 1

If your trailer is single axle you would need a Load Range D like the part #LHAW121 which has a capacity of 2,150 lbs at 65 psi since you have a 4,000 lb trailer. What is also great about the tire on this combo is that it is rated for up to 75 mph…

view full answer...

Answer 2

The etrailer #CA-5400-B weld-on coupler you were looking at would be a great replacement for your current Parker Performance A-frame coupler. This coupler has a 2-5/16 inch ball and a weight capacity of 14,000lbs. I have linked this product to this…

view full answer...

Answer 3

For your Shelby 5104 trailer coupler I recommend the Round A-Frame Trailer Jack - Sidewind - 15-5/8" Travel - 5,000 lbs #TJA-5000S-B. This will use the Footplate for 2,000-lb and 5,000-lb Round, A-Frame Jacks #JF-99.

view full answer...

Answer 4

It looks like you need a trailer coupler repair kit for your trailer coupler. If that is the case then I would love to help but unfortunately I cannot identify the correct replacement coupler repair kit for you based on the photo you have attached.…

view full answer...

Answer 5

The A-Frame Trailer Coupler - Thumb Latch - Black - 2-5/16" Ball - Weld On - 14,000 lbs #CA-5400-B is designed to fit over the frame of your trailer and sit flat. The angle of the trailer frame to the bottom of the coupler shouldn't change…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

I checked your order notes and the leaf springs you bought last year were the part #e28SR which are for 5k axles. Since this is over the capacity of your axle failure would not have been caused by over loading the trailer assuming you stayed under…

view full answer...

Answer 8

The Dexter 072-078-00 is a 2,200 lb capacity leaf spring. You can use a higher capacity leaf spring, however it won't increase the capacity of your trailer as the axle is still rated for that max capacity of 4,400 lbs. My recommendation for a…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

I really wish we had replacement parts still for the Atwood couplers but since they've been out of business for so long we don't have any way to get the parts you are wanting.

view full answer...

Answer 11

While we don't' have custom 5th wheel or rear hitch options for your 2005 Freightliner M2 106 you can mount the Reese low-profile hitch, #RP30054. It requires a little custom fabrication which is explain in the linked instructions. For a rear…

view full answer...

Answer 12

Yes, the Solera Slide Topper part #LCV000168106 is the correct fit for your flange width of 90-1/2 inches. This specific model has a box width range of 86 to 91-3/4 inches which is perfect for your width listed.

view full answer...

How Do I Get a VIN Number For My New Trailer?

Product Page this Question was Asked From

Continue Researching