Where To Mount Stabilizer Jacks In the Front Of Winnebago View

Question

Question:

I already mounted 2 stabilizer jacks where the 2 skids used to be where can I mount them on the front, purely for stabilization?

asked by: Larry E

0

Expert Reply:

Typically you mount stabilizer jacks like Item # TJ01RT under the corners of your camper. These jacks have a 650-lb capacity, are sold individually, and are designed to keep your camper level and steady. They have a bolt-on or weld-on installation and you will need to use your own hardware to mount them.

You will also need a handle rod like Item # SJ-100-HD to easily fine-tune your height.

I have attached some videos for you to check out.

expert reply by: Brint H

0

Answer 1

Most likely it would work fine. Most of these are 1/2 inch in diameter like the part #SJ-100-HD that you referenced. If yours needs a 1/2 inch diameter rod this would work well.

view full answer...

Answer 2

The length of the Replacement Handle Rod #SJ-100-HD is 11-3/4 inches.

view full answer...

Answer 3

The stabilizer jack I recommend for your enclosed cargo trailer is the Drop Leg Stabilizer Jack #TJ01RT because it will work well to stabilize your trailer for loading and unloading and is easy to engage when needed. The #TJ01RT drop leg stabilizer…

view full answer...

Answer 4

There many possible ways to mount a stabilizer jack such as the #TJ01RT-HD you looked at. Mounting them in the orientation shown the diagram would tend to work a bit better to stabilize the trailer against side to side movement, while having the…

view full answer...

Answer 5

It should fit perfectly, but because the Atwood jack has been discontinued for awhile and I can't confirm it for myself I'd recommend simply measuring the diameter of the hole in the assembly where the jack handle installs. If that hole…

view full answer...

Answer 6

The diameter of the Replacement Handle Rod #SJ-100-HD you referenced is 1/2 inch.

view full answer...

Answer 7

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Where To Mount Stabilizer Jacks In the Front Of Winnebago View

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching