How to Add a 7-Way Trailer Connector to a 1996 Ford F-250

Question

Question:

Looking for a 7 pin connector that will plug into my factory plugs. 1996 F250, will item 118242 work on my truck? thanks

asked by: Keith

0

Expert Reply:

I do have an option for you but the Ford Replacement OEM Tow Package Wiring Harness part # 118242 is not a confirmed fit for your 1996 Ford F-250. The best option for you will depend on if your truck came with a factory 4-way trailer connector or not.

If your truck did come with a factory 4-way trailer connector then you are going to want to use part # ETBC7. If your truck did not come with a factory 4-way trailer connector then you are going to want to use both part # 118316 and part # ETBC7.

These are currently the only options we have for you to add a 7-way trailer connector to your F250. They will require splicing but this is the only option as your truck did not come with a plug-in adapter.

expert reply by: Conner L

0

Answer 1

There are a few scenarios here. If you have a factory-installed 4-way connector then that makes a difference down the road when installing a brake controller. There may be a brake controller port under the dash on your F-250 and an adapter can be…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 6

If your Ford F-450 has an actual bed and is not a cab and chassis model (with a service bed or flatbed) then you can use the Curt universal folding gooseneck ball rail kit #C61502. You could then use Curt hitch #C-52 or #C65500. A custom hitch for a…

view full answer...

Answer 7

You can use the RV Propane Gas Detector #RS64FR to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 10

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 11

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 12

The Curt T-Connector #C56093 is a great place to start with wiring on your 2024 Ford Explorer. To get your vehicle ready for your trailer I recommend the following parts: - Universal Installation Kit #ETBC7 - Redarc Tow-Pro Liberty Brake Controller…

view full answer...