Tips for Installing EX1033 Hinge on Extang Trifecta Tonneau

Question

Question:

Is there a technique to installing the hinge? I was able to get the old hinge out with a screwdriver but getting the replacement hinge in the groove of the cover is extremely difficult. I must be doing something wrong. Any advice would be greatly appreciated.

asked by: Dale

0

Expert Reply:

I emailed Extang for tips on installing the hinge part # EX1033 and this is what they sent back:

"The hinges should just slide into the rails of the cover. It is easier when the cover is folded open and you are putting both sides of the hinge in at once.

Please let me know if you need anything further."

expert reply by: Jameson C

0

Answer 1

The Extang #EX1032 replacement hinge that you referenced is made for Extang Trifecta and Extang eMAX folding tonneau covers as a hinge replacement. I reached out to my contact at Extang and found out that they also make the Gator covers and that this…

view full answer...

Answer 2

We do not offer any replacement parts that directly are for your Gator tonneau cover, however Extang also made Gator covers so their tailgate hinge #EX1033 and their cab side hinge #EX1032 may work for you, however you're going to want to make…

view full answer...

Answer 3

Extang doesn't have written instructions or a video, but the process is simple enough that I'm pretty confident I can talk you through it. Fold the cover open to access the hinge assemblies. You'll see that the hinge assembly is held on…

view full answer...

Answer 4

You would want the whole hinge assembly, #EX1033, especially if you have frequent breakage like you have described. There could be fatigue to the other components so to ensure maximum longevity I do recommend the whole hinge assembly. It is possible…

view full answer...

Answer 5

I've confirmed with Extang that the #EX1033 you mentioned is indeed the correct replacement hinge for the panel closest to the tailgate. It is compatible with the first generation Extang Trifecta you have.

view full answer...

Answer 6

We do have that part for you! The correct part is the Replacement Tailgate Hinge for Extang Trifecta and eMax Tonneau Covers #EX1033. This is the same part as Extang's 35440400 that you reference.

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Thanks for reaching out, Joe! I recommend using the Rhino-Rack Aero Bar Roof Rack for Camper Shells #Y02-480B which comes with 63" long tracks as well as 54" long crossbars which should give you a little bit of overhang on your canopy. Per…

view full answer...

Answer 9

Yes you are - all 5th wheel hitches are going to require some type of rails in order to be used. So you'd need #DM8552016-71 for your 2006 Dodge Ram.

view full answer...

Answer 10

I attached a picture to this page that has a wiring diagram for the Furrion Indoor Enclosed Amplified Subwoofer #FSW8P12CF that you referenced. I attached a review video for this for you to check out as well.

view full answer...

Answer 11

The Class V hitch we have for your 2004 Dodge Ram 2500 with the best ground clearance is the Curt hitch part #C15809. It doesn't tuck right under the rear bumper like what you can see in the attached picture but it does sit the highest.

view full answer...

Tips for Installing EX1033 Hinge on Extang Trifecta Tonneau

Product Page this Question was Asked From

Continue Researching